The technical material below is retained for this model only. Do not transfer a range, pulse, interface, mechanical or safety value from another 1535 nm product.
Specifications
LRF0612C is a 1535 nm pulsed distance-measurement module. Its assigned laser source is ER200; receiver-component data below come from the supplied APD-A13B001 R01 document. The three specification levels describe different assemblies and measurement conditions.
1. LRF0612C module specifications
Source clarifications
The current PDF shows a six-contact connector but describes only five contacts. No sixth-contact function is inferred. Its average-power row leaves the frequency after “@” blank; no measurement rate is assigned to that power figure.
LRF0612C — TECHNICAL SPECIFICATIONS
| Project |
Performance Indicators |
| Model |
LRF0612C |
| Laser Wavelength |
1535±5nm |
| Module laser-safety statement |
Class I stated in the module document. Final accessible-emission classification applies to the complete configuration. |
| Divergence Angle |
≤0.3 mrad |
| Laser Energy |
≥200 μJ |
| Launch Lens Diameter |
Φ12 mm |
| Receiver Lens Diameter |
Φ25 mm |
| Measuring Range
（Reflectance 30%; visibility ≥ 8 km.）
|
Reference target(2.3m×2.3m) ≥6000m
Measuring human target(0.5m×1.7m) ≥1200m
|
| Minimum Range |
≤50 m |
| Ranging Frequency |
1Hz ~10Hz |
| Number of multi-target detections |
Up to 3 targets |
| Ranging Accuracy |
±2 m |
| Range Resolution |
≤0.1m |
| Precision Rate |
≥98% |
| False Alarm Rate |
≤1% |
| Pin-in-lead package model |
A1257WR-S-6P |
| Supply Voltage |
DC 4.5～16 V |
| Standby power consumption |
≤1 mW |
| Average power consumption |
≤4 W (measurement-rate condition not specified) |
| Peak Power Consumption |
≤14W @12 V |
| Weight |
≤ 58±1g |
| Dimension (L×W×H) |
65mm×48mm×32 mm |
| Operating Temperature |
-40～+70 ℃ |
| Storage Temperature |
-55～+75 ℃ |
| Impact Resistance |
Meet the MIL-STD-810G testing standard |
| Vibration Resistance |
Meet the MIL-STD-810G testing standard |
LRF0612C — PIN interface
| Pin |
Definition |
Description |
Cable color |
| 1 |
Positive power supply |
Power supply, 4.5 ~ 16V |
Red |
| 2 |
Negative power supply |
Power supply, ground |
Black |
| 3 |
POWER_ON |
Module power switch, TTL_ 3.3V level;
Module on (> 2.7V), module off (< 0.3V);
|
White |
| 4 |
UART_TX |
Serial port sender, TTL_ 3.3V level |
Yellow |
| 5 |
UART_RX |
Serial port receiver, TTL_ 3.3V level |
Green |
Model-specific mechanical and interface drawings
LRF0612C: OUTLINE DIMENSION(mm). Original model-bound drawing.
LRF0612C: PIN interface. Original model-bound drawing.
2. ER200 source-laser specifications
ER200 standalone laser component
| Parameter | Value |
| Optical wavelength |
1535 nm |
| Pulse energy |
200 µJ (source value; no minimum/maximum qualifier) |
| Optical pulse width |
5 ns (FWHM) |
| Drive pulse width |
<2.4 ms |
| Repetition rate |
10 Hz (source operating point, not a stated range) |
| Pulse-energy stability |
10% (definition/statistical method not stated) |
| Raw beam diameter |
0.3 mm |
| Initial beam divergence |
8 mrad (source value; no ≤ qualifier) |
| Transverse mode |
TEM00 |
| Operating / storage temperature |
−40 to +65 °C / −55 to +85 °C |
| Package dimensions / mass |
21 × 8 × 6.8 mm / 7 g |
| Component electrical entry |
2 V, 10 A |
| Shock / vibration entries |
1500 G, 0.5 ms / 20–2000 Hz, 20 G |
| Stated service life |
>1 million shots; test conditions not supplied |
The electrical entries describe the component drive, not the module supply input. Drive conditions and pulse-width definitions must follow the component document and the individual factory record. An optical pulse-width value is not a pump-drive duration.
3. APD-A13B001 receiver-component specifications
Small screens: swipe the table horizontally to read all measurement conditions.
Supplied APD200 document — component values and conditions
| Parameter | Value | Measurement condition / scope |
| Device / active diameter |
APD-A13B001 R01 / 200 µm |
Supplied APD200 document, p1 |
| Detector spectral response interval |
800–1700 nm |
Detector response; not the filter passband |
| Responsivity |
0.9 A/W minimum; 1.0 A/W typical |
λ = 1550 nm; incident power = 1 µW; M = 1 |
| Dark current |
8 nA typical; 50 nA maximum |
VR = VBR − 3 V; incident power = 0 |
| Multiplication factor |
M ≥10 / M ≥30 |
λ = 1550 nm; 1 µW; respectively VBR − 3 V / VBR − 1 V |
| −3 dB bandwidth |
0.6 GHz minimum; 1.25 GHz typical |
M = 10; RL = 50 Ω |
| Breakdown voltage |
35–50 V |
Reverse current = 10 µA; incident power = 0 |
| Capacitance |
1.8 pF typical; 2.0 pF maximum |
VR = VBR − 3 V; f = 1 MHz |
| Breakdown temperature coefficient |
0.05 minimum / 0.11 typical / 0.15 maximum V/°C |
Reverse current = 10 µA; dark; −55 to +85 °C |
| Operating / storage temperature |
−40 to +85 °C / −55 to +125 °C |
Component absolute-maximum table; not module environmental ratings |
| Maximum bias |
VBR |
Absolute maximum, not a recommended operating setpoint |
| Maximum forward / reverse current |
5 mA / 3 mA |
Absolute maximum ratings, not continuous design targets |
| Filter centre wavelength |
1535 ±5 nm |
Supplied filter table, p3 |
| Filter FWHM |
<37 nm |
Full width at half maximum |
| Transmission at centre wavelength |
>90% |
Filter specification, not total receiver throughput |
| Blocking specification |
T <1%; source lists 400–1750 nm |
Stop-band/transition edges are not numerically defined; the stated blocking span is not a guarantee at every wavelength. |
| Optical surface quality |
60/40 |
Source label: surface quality; not a transmission value |
