The technical material below is retained for this model only. Do not transfer a range, pulse, interface, mechanical or safety value from another 1064 nm product.
Specifications
The tables below retain the supplied model record except for entries explicitly withheld after a comparison with the current model PDF. A value, option or condition from another model is not interchangeable. General explanations are separated from model-specific entries.
Source-review note
The document contains conflicting near-distance statements and differing timing-tolerance wording. The old pulse-width transcription also contains an ambiguous character. A corrected controlled source is required for the withheld fields.
Current LR160 document — source checked 13 September 2026. On a small screen, swipe wide tables horizontally to read every column.
LR160 — TECHNICAL SPECIFICATIONS
|
Laser Wavelength
|
1064nm±1nm
|
|
Laser Energy
|
85 mJ and 160 mJ (switchable)
|
| Optical Delay |
Withheld pending a corrected, controlled model specification. See the source-review note above. |
|
Beam Divergence
|
≤0.2mrad
|
|
Laser Designation Frequency
|
8～21Hz
|
|
Ranging Frequency
|
10Hz
|
| Laser Pulse Width |
Withheld pending a corrected, controlled model specification. See the source-review note above. |
|
Power Stability
|
≤8%
|
| Ranging Range |
Withheld pending a corrected, controlled model specification. See the source-review note above. |
|
Ranging Error
|
≤5m
|
|
Target Selection
|
First Target / Second Target / Last Target
|
|
Valid Measurement Rate
|
98%
|
|
Trigger Mode
|
Internal Sync Illumination, External Sync Illumination
(Trigger Delay: 304.0 μs ± 0.1 μs)
|
|
Dimensions
|
≤306×145×94mm
|
|
Weight
|
≤3.3kg
|
|
Laser Designation Performance
|
Laser Designation Center Frequency: 20 Hz
Low/Normal Temperature, 85 mJ Output
Laser designation time: 90 s, rest: 60 s, 5 consecutive cycles
Low/Normal Temperature, 160 mJ Output
Laser designation time: 60 s, rest: 60 s, 5 consecutive cycles
High Temperature, 85 mJ Output
Laser designation time: 90 s, rest: 60 s, 1 cycle
High Temperature, 160 mJ Output
Laser designation time: 60 s, rest: 60 s, 1 cycle
|
|
Ranging Performance
|
Minimum Measuring Distance: ≤ 300 m
Maximum Measuring Distance: ≥ 30 km
(target size 10 m × 10 m × 8 m, diffuse reflectivity ≥ 0.2, visibility ≥ 30 km, relative humidity ≤ 70%)
Ranging Frequency: 10 Hz (up to 3 targets)
Continuous Operating Cycles:
l Low/Normal Temperature:
Operate 5 minutes, rest 4 minutes, 5 consecutive cycles
l High Temperature, 85 mJ Output:
Operate 5 minutes, rest 4 minutes, 2 consecutive cycles
l High Temperature, 160 mJ Output:
Operate 2 minutes, rest 4 minutes, 2 consecutive cycles
|
|
|
RS422
|
| External Synchronization Interface |
Withheld pending a corrected, controlled model specification. See the source-review note above. |
|
Coding Mode
|
Precise frequency coding and time coding
|
|
Period Accuracy
|
<±1us
|
|
Power Supply
|
DC 24V±4V
|
|
Startup Time
|
< 1 minute (at room temperature)
|
|
Low Temperature
|
Operating temperature: −40 °C
Storage temperature: −45 °C
|
|
High Temperature
|
Operating temperature: +60 °C
Storage temperature: +65 °C
|
LR160 — PIN INTERFACE
|
J30J-21ZKP
|
|
Pin
|
Function
|
Description
|
Direction
|
Remarks
|
|
1
|
TX+
|
RS-422 TX+
|
Output
|
RS-422 Communication Interface
|
|
2
|
TX-
|
RS-422 TX−
|
Output
|
|
3
|
RX+
|
RS-422 RX+
|
Input
|
|
4
|
RX-
|
RS-422 RX−
|
Input
|
|
5
|
GND
|
RS-422 GND
|
GND
|
|
6
|
EN+
|
Power Enable
|
|
24 V Power Enable Switch
|
|
7
|
EN-
|
Power Enable
|
|
|
8-13
|
|
Not Connected / NC
|
|
|
|
14
|
A
|
External Sync Differential + (A)
|
Input
|
A and B are the A/B differential outputs of the RS-422 driver chip
|
|
15
|
B
|
External Sync Differential − (B)
|
Input
|
|
16
|
LED+
|
DC5V
|
Input
|
Laser Designation Power Supply
|
|
17
|
LED-
|
GND
|
Input
|
|
18-21
|
|
|
|
|
LR160 — PIN INTERFACE
|
J30J-04ZK
|
|
Pin
|
Function
|
Description
|
Direction
|
Remarks
|
|
A、B
|
24V
|
Power Supply
|
Input
|
Red
|
|
C、D
|
GND
|
Power GND
|
Input
|
Black
|
Technical drawings
LR160 — OUTLINE DIMENSION(mm)
