Home >  Turbine & EDF Jet >  Jetcat Turbine Engine > Jetcat Turbine 30kg Thrust P300-Pro Kero Starter GH Version

Jetcat Turbine 30kg Thrust P300-Pro Kero Starter GH Version (Global Warehouse)

  • Status : In StockSKU:24050
  • Was:0
  • Now:
    0


      Qty.Range(unit) Price(per unit) Discount
      1 0 No
    Wholesale inquiry
    Quote the freight after you click "Add to Cart"

    Customers Who Bought This Item Also Bought

    • Product Details
    • Manual
    • Video
    • Spare Parts

    FOR PRODUCT MANUAL, CLICK https://www.austars-model.com/products_reviews.html 

    The JetCat PRO turbines offer maximum integration and installation. All system equipment required for turbine operation is fully integrated under the turbine hood. Apart from the supply battery, the fuel tank and the control signals, no further external subsystems are required! The control signals are output on a data cable terminated with a 15-pin SUB-D connector. Power is optionally supplied via the power cable with XT60 plug for direct battery connection.

    JetCat-PRO turbine functions:

    Integrated turbine components:

    • ECU (electronic control unit)
    • Integrated brushless fuel pump
    • Fuel and kerosene start valves
    • fuel filter
    • kerosene starter
    • Barometric height / pressure sensor
    • 4-pole Molex extension plug (e.g. for smoke pumps / fuel pump)
    • Vent opening with integrated one-way valve (e.g. for pressurizing the fuel system)

    power supply:
    Over 3 cells LiPo battery / XT60 connection / capacity 3000mAh or higher

    Data connector (section)
    Over 15-pin SUB-D (male) there are the following control options:

    • 1x PowerOn control signal
    • 2x PWM input channels (e.g. for RC remote control; THR / AUX)
    • 2x independent RS232 interfaces for computer remote control and / or interconnection of several turbines
    • 1x Analog voltage regulation / sensor input
    • 1x JetCat bus interface, e.g. for connection of GSU and / or other JetCat accessories (LCU / flow sensor / BMS system etc.) CAN bus interface for control and data reporting

    Standard Version:
    The standard P300-PRO Engines have a "normal" starter motor, without generator (to save costs, e.g. for hobby applications). With our "JetCat-PRO" interface, the Engines can easily be used for RC model applications. The PRO interface has already integrated the full functionality of our telemetry adapter!

    Generator Version PRO-GL:

    These versions consist of a brushless and non-contact starter/generator system. The generator is "soft coupled", i.e. it rotates at a lower speed than the turbine shaft itself (patent pending). A built-in and integrated DC / DC converter with additional charge control enables buffering / recharging of the turbine battery. The charging system is able to supply charging energy to the Engine battery at idling speed. The electrical power of this charging system is approx. 85W. The "soft" coupling of the generator limits the power output.

    Generator Version PRO-GH:

    This version consists of a brushless and non-contact starter/generator. The generator is "hard" coupled to the turbine shaft (but there is no mechanical contact), i.e. it rotates at the same speed as the turbine. This configuration allows a much higher power output of the generator (900W!). This version is also supplied with an unregulated 3-phase alternating current supply. The three-phase voltage varies proportionally with the turbine speed. Typically, the measured no-load DC voltage is approximately 12V / 7.5A (33,000 1 / min) and 35V / 22A (100,000 1 / min) when charged with a 1.5 Ohm resistor behind a rectifier network (6x High Power Schottky diodes).

     

    NameValue
    Pressure ratio 3,55
    Mass flow (kg/s) 0,5
    Consumption Full load (ml/min) 980
    Consumption idle (ml/min) 179
    Weight [g] 2730
    Dimensions of the diameter (mm) 132
    Length (mm) 380,5
    Battery recommendation
    Carton dimensions (LxWxH; cm)
    Exhaust gas temperature (°C) 480-750
    Idle speed (1/min) 35000
    Max rpm (1/min) 105000
    Thrust at idle (N) 14
    Thrust @ maxRpm (N) 300
    Exhaust gas velocity (km/h) 2160
    Exhaust gas power output (kW) 90
    SFC @ maxRpm (kg/Nh) 0,157



    Customer Photos

    No Photos! Be the first to of this product! and get AM points!


    Customer Videos

    No Videos! Be the first to of this product! and get AM points!


    Customer Reviews

    howtowin.jpg

     winacar.jpg

    If you have already bought this product, please click here to write a review and get 5-30 AM Points.
    If you are considering buying this product, please click here to submit your enquiry, or see enquiries from other customers.
    For any after sales questions, please Contact Customer Service and get a response within 24 hours.
     
    Average Rating: 4.7 stars 0  (see all 0 customer reviews)
    Any customer writing a review can get AM points, the first five get double AM points (see Austars-Model Points & Rewards
    Customer Inquiries
    If you have any questions about this product, delivery, payment options, etc, please feel free to submit your enquiry. We will reply to you within 24 hours.
         
    For any after sales questions, please Contact Customer Service and get a response within 24 hours
         

    Copyright © 2007-2015 austars-model.com All Rights Reserved.
    evening dresses Wedding Party Dresses bridesmaid dresses Robe De Mariée Robe Demoiselle D'honneur Robe De Soirée