1. Specification

1.1 Output: Continuous 10A, Burst 12A up to 10 Secs.
1.2 Input Voltage: 2-4 cells lithium battery or 5-12 cells NiCd/NIMh battery.
1.3 BEC: 1A / 5V (Linear mode).
1.4 Max Speed: 210,000rpm for 2 Poles BLM, 70,000rpm for 6 poles BLM, 35,000rpm for 12 poles BLM.
1.5 Size:27mm (L) * 17mm (W) * 6mm (H).
1.6 Weight:g.

2. Feature:

2.1 Safety Arming Feature:Regardless the throttle stick position, the motor will not spin after battery connected.
2.2 Throttle Calibration: Throttle range can be configured to provide best throttle linearity, fully compatible with all market available transmitters.
2.3 Programmable Items.
Brake Setting: brake enabled / brake disabled.
Battery Type: Li-xx(Li-ion or LiPo) / Ni-xx(NiMh or NiCd).
Low Voltage Protection Mode(Cutoff Mode): Gradually reduce the output power / Cutoff the output power.
Low Voltage Cutoff Protection Threshold (Cutoff Threshold): low / medium / high.
Start Mode: normal / soft / very soft.
Timing: low / medium / high.
Reset: reset all the programmable items to their default settings.
2.4 Full Protection Features: Low voltage cutoff protection / Over-heat protection / Throttle signal lost protection.

3. Advantages:

3.1 Military standard capacitor of extreme low resistance increases the ability of prevention of unwanted RF noise during flying.
3.2 Extreme low resistance PCB is helpful for getting a super current endurance capability.
3.3 Microprocessor uses separate voltage regulator IC, with good anti-jamming capability.
3.4 Compatible with Hobbywing's Program Card

1. Specification

1.1 Output:Continuous 12A, Burst 15A up to 10 Secs.
1.2 Input Voltage: 2-4 cells lithium battery or 5-12 cells NiCd/NIMh battery.
1.3 BEC: 2A/5V (Linear mode).
1.4 Max Speed: 21OOOrmp for 2 Poles BLM, 70,000rpm for 6 poles BLM, 35,000rpm for 12 poles BLM.
1.5 Size:32mm (L) * 24mm (W) * 10mm (H).
1.6 Weight:13g.

2. Feature:

2.1 Safety Arming Feature:Regardless the throttle stick position, the motor will not spin after battery connected.
2.2 Throttle Calibration: Throttle range can be configured to provide best throttle linearity, fully compatible with all market available transmitters.
2.3 Programmable Items.
Brake Setting: brake enabled / brake disabled.
Battery Type: Li-xx(Li-ion or LiPo) / Ni-xx(NiMh or NiCd).
Low Voltage Protection Mode(Cutoff Mode): Gradually reduce the output power / Cutoff the output power.
Low Voltage Cutoff Protection Threshold (Cutoff Threshold): low / medium / high.
Start Mode: normal / soft / very soft.
Timing: low / medium / high.
Reset: reset all the programmable items to their default settings.
2.4 Full Protection Features: Low voltage cutoff protection / Over-heat protection / Throttle signal lost protection.

3. Advantages:

3.1 Military standard capacitor of extreme low resistance increases the ability of prevention of unwanted RF noise during flying.
3.2 Extreme low resistance PCB is helpful for getting a super current endurance capability.
3.3 Microprocessor uses separate voltage regulator IC, with good anti-jamming capability.
3.4 Compatible with Hobbywing's Program Card

Specification:
1.1 Output: Continuous 18A, Burst 22A up to 10 Secs.
1.2 Input Voltage: 2-4 cells lithium battery or 5-12 cells NiCd/NIMh battery.
1.3 BEC: 2A / 5V (Linear mode).
1.4 Max Speed: 210,000rpm for 2 Poles BLM, 70,000rpm for 6 poles BLM, 35,000rpm for 12 poles BLM.
1.5 Size: 45mm (L) * 24mm (W) * 11mm (H).
1.6 Weight: 19g.

Features:
2.1 Safety arming feature:?egardless the throttle stick position, the motor will not spin after battery connected.
2.2 Throttle calibration: Throttle range can be calibrated to be compatible with different transmitters.
2.3 Programmable Items:
Brake Setting: brake enabled / brake disabled.
Battery Type: Li-xx(Li-ion or LiPo) / Ni-xx(NiMh or NiCd).
Low Voltage Protection Mode(Cutoff Mode): Gradually reduce the output power / Cutoff the output power.
Low Voltage Cutoff Protection Threshold (Cutoff Threshold): low / medium / high.
Start Mode: normal / soft / very soft.
Timing: low / medium / high.
Reset: reset all the programmable items to their default settings.

Advantages:
3.1 Military standard capacitor of extreme low resistance increases the ability of prevention of unwanted RF noise during flying.
3.2 Extreme low resistance PCB is helpful for getting a super current endurance capability.
3.3 Microprocessor uses separate voltage regulator IC, with good anti-jamming capability.
3.4 Compatible with Hobbywing's program card.

Pentium-30A is ESC product in "PENTIUM" series. "PENTIUM" series has the full range of ESCs from 6A to 100A.

1 Specification

1.1 Output: Continues 30A, Burst 40A up to 10 Secs.

1.2 Input Voltage: 5.6V --- 16.8V ( Lithium : 2 – 4s or NiMH/NiCd 5 -12 Cells)

1.3 BEC (Battery Elimination Circuit) Output?linear mode BEC 2A

1.4 Max Speed: 210,000rpm for 2 Poles BLM, 70,000rpm for 6 poles BLM, 35,000rpm for 12 poles BLM. (BLM: BrushLess Motor)

1.5 Size?24mm*45mm*11mm(width*length*height)

1.6 Weight: 25g

1.7 Packaging include:

3 sets of gold plated motor connectors and heat-shrink tubings (Remark: motor connectors and heat-shrink tubings need to be purchased additionally)

2 Features

2.1 Safety Arming Feature: Regardless the Throttle Stick position, the motor will not spin after battery connected. This will prevent any injury happened.

2.2 Throttle Calibration: Throttle range can be configured to provide best throttling linearity, fully compatible with all market available transmitters.

2.3 Programmable Items:

-Brake Settings?brake enabled / brake disabled, default is brake disabled

-Battery Type?Li-xx(Li-ion or Li-poly) / Ni-xx(NiMh or Nicd)?default is Li-xx.

-Low Voltage Protection Mode(Cutoff Mode) ?power reducing / power cutoff, default is power reducing.

-Low Voltage Protection Threshold(Cutoff Threshold) ?low / medium / high, default is medium cutoff voltage.

1) For Li-xx battery?number of battery cells are judged automatically?low / medium / high cutoff voltage for each cell are: 2.6V/2.85V/3.1V. For example: 3 Cells Li-Poly, when medium cutoff voltage is set, the cutoff voltage is: 2.85*3=8.55V.

2) For Ni-xx battery, low / medium / high cutoff voltages are 0%/45%/60% of the startup voltage (0% means the low voltage cutoff protection function is disabled) . For example: a 10 cells NiMH battery pack, fully charged voltage is 1.44*10=14.4V, when medium cutoff voltage is set, the cutoff voltage is : 14.4*45%=6.5V.

-Startup mode: normal / soft / super-soft, default is normal startup.

-Timing: low / medium / high, default is medium timing. In normal cases, low timing can be used for most motors. But for high efficiency, we recommend the Low timing for 2 poles motor and Medium timing for 6 poles and above. For higher speed, High timing could be used.

2.4 Full Protection Features: Low-voltage cutoff protection / over-heat protection / throttle signal lost protection.

3 Advantages

3.1 Military Standard Capacitor with extremely low resistance used on voltage input section, this will increase the ability of prevention of unwanted RF Noise/ Interference during flying.

3.2 Extreme low resistance, super current endurance.

3.3 Microprocessor and BEC use separate voltage regulator IC, with good anti-jamming capability.

3.4 Compatible with Hobbywing's Program Card .

3.5 Own complete intellectual property rights.

Product Description

The Xrotor series ESC is a new and independent series hobbywing created based on the performance requirement on multi-rotor aircraft. The XRotor seriers speed controllers have significant improvements in throttle response, compatibility, usability over the existing series ESCs for aircrafts.

Main Features:

1.1 Special core program for multi-rotor controllers greatly improves throttle response.
1.2 Specially optimized software for excellent compatibility with disc-type motors.
1.3 All settings except the timing are preset, making usage simple, highly intelligent and adaptive.
1.4 The twisted-pair design of the throttle signal cable effectively reduces the crosstalk produced in signal transmission and makes flight more stable.
1.5 Compatible with various flight-control systems and supports a signal frequency of up to 621Hz (Note: all throttle signals over 500Hz are non-standard signals) .
1.6 Special drive chip has much better MOSFET driving effect than common driving circuit consisted of discrete components.
1.7 MOSFET with extra-low resistance brings high performance and great current endurance.
1.8 The high-light LEDs save the trouble of mounting any extra color light on multi-rotors.
1.9 The dip switches at the bottom of the ESC control the ON/OFF status, color of the LED light, timing, and the motor rotation.

Speicifications:

Compatibility Test

The Xrotor series ESC is a new and independent series hobbywing created based on the performance requirement on multi-rotor aircraft. The XRotor seriers speed controllers have significant improvements in throttle response, compatibility, usability over the existing series ESCs for aircrafts.

Main Features:

1.1 Special core program for multi-rotor controllers greatly improves throttle response.
1.2 Specially optimized software for excellent compatibility with disc-type motors.
1.3 All settings except the "Timing" are preset, making usage simple, highly intelligent and adaptive.
1.4 The twisted-pair design of the throttle signal cable effectively reduces the crosstalk produced in signal transmission and makes flight more stable.
1.5 Compatible with various flight-control systems and supports a signal frequency of up to 621Hz (Note: all throttle signals over 500Hz are non-standard signals) .
1.6 Special drive chip has much better MOSFET driving effect than common driving circuit consisted of discrete components.
1.7 MOSFET with extra-low resistance brings high performance and great current endurance.

Specifications:

Compatibility Test

The Xrotor series ESC is a new and independent series hobbywing created based on the performance requirement on multi-rotor aircraft. The XRotor seriers speed controllers have significant improvements in throttle response, compatibility, usability over the existing series ESCs for aircrafts.

Main Features:

1.1 Special core program for multi-rotor controllers greatly improves throttle response.
1.2 Specially optimized software for excellent compatibility with disc-type motors.
1.3 All settings except the "Timing" are preset, making usage simple, highly intelligent and adaptive.
1.4 The twisted-pair design of the throttle signal cable effectively reduces the crosstalk produced in signal transmission and makes flight more stable.
1.5 Compatible with various flight-control systems and supports a signal frequency of up to 621Hz (Note: all throttle signals over 500Hz are non-standard signals) .
1.6 Special drive chip has much better MOSFET driving effect than common driving circuit consisted of discrete components.
1.7 MOSFET with extra-low resistance brings high performance and great current endurance.

Specifications:

Compatibility Test

The Xrotor series ESC is a new and independent series hobbywing created based on the performance requirement on multi-rotor aircraft. The XRotor seriers speed controllers have significant improvements in throttle response, compatibility, usability over the existing series ESCs for aircrafts.

Main Features:

1.1 Special core program for multi-rotor controllers greatly improves throttle response.
1.2 Specially optimized software for excellent compatibility with disc-type motors.
1.3 All settings except the "Timing" are preset, making usage simple, highly intelligent and adaptive.
1.4 The twisted-pair design of the throttle signal cable effectively reduces the crosstalk produced in signal transmission and makes flight more stable.
1.5 Compatible with various flight-control systems and supports a signal frequency of up to 621Hz (Note: all throttle signals over 500Hz are non-standard signals) .
1.6 Special drive chip has much better MOSFET driving effect than common driving circuit consisted of discrete components.
1.7 MOSFET with extra-low resistance brings high performance and great current endurance.

Specifications:

Compatibility Test

June 15th, 2012, famous brushless ESC manufacturer Hobbywing released the world`s first 4in1 20A high performance brushless ESC--Skywalker Quattro 20Ax4-UBEC (abbr:SQ20A4U), this ESC is suitable for multirotor aircraft, and four-motor airplane or four-propeller ship model. Integrated design can not only offer better consistency, but also simplify wiring complexity, so as to improve work reliability.

MultiRotor Flyer has been very popular as a new generation of RC model aircraft, which is simple structure, light weight and easy to fly. However, as there are four motors in the four corners, normally there are four ESCs to control each motor, which is complicated to assembly and set up. Since HobbyWing has developed the SkyWalker-Quattro-20A ESC, problems will be solved.

The SkyWalker-Quattro-20A ESC combines four 20A ESCs together, useable with 2~4 LiPo cell packs, it also has a 5V/3A BEC inside. Four motors now can directly connected to the ESC, no more complicated wiring stuff or set up procedures.

The SkyWalker-Quattro-20A ESC combines four high performance 20A ESC and 5V/3A UBEC, wherein the ESC is based on standard PWM control signal. This SQ20A4U has absolutely strong compatibility, which can work with most FC and radio set. Each ESC can separately perform throttle trip correction and other work parameter setting. The default parameter could satisfy most application requirements.

Main feature of Hobbywing SQ20A4U:
- 4 speed controllers in 1 board, only 1 pair of battery wire is required.
- Powerful switch model built-in BEC (the BEC voltage outputs from the S3 connector)
- Multiple protection features: Low voltage cut-off protection/ over-head protection/ throttle signal loss protection.
- The throttle range of each ESC can be calibrated to be suitable for different multi-rotor flying control systems/transmitters.
- Maximum speed: 210000 RPM (2 poles motor), 70000 RPM (6 poles motor),35000 RPM (12 poles motor).

Specification of Hobbywing SQ20A4U:
- Cont. current: 20A x 4
- Burst current: 25A x 4 (>10s)
- BEC mode: Switch mode
- BEC output: 5V/3A
- Battery cell: 2S-4S (7.4V-14.8V)
- Size: 70mm x 62mm x 11mm
- Weight: 112g

Feature:
Profit Technology latest multi-rotor aircraft designed for multi-rotor aircraft research and design, a number of optimization.

-Use a high-performance processor, has excellent compatibility and high motor drive efficiency. The maximum speed of the motor can reach 210000 RPM (2-pole motor), 70000 RPM (6 poles motor), 35000 RPM (12 poles motor).

-Ordinary start / soft start / super soft and start" the three startup mode, compatible with fixed-wing aircraft and helicopters.

-You can set the throttle, compatible with all commercially available remote control. Possess a smooth, delicate the governor feel, class speed linear and extremely fast throttle response speed.
-Microprocessor uses separate voltage regulator IC, with better anti-interference ability, greatly reducing the possibility of out-of-control.

-With input voltage abnormal protection / battery low voltage protection / over-temperature protection / throttle signal lost protection "multiple protection features, effectively extending the life of the ESC.
-Built-in BEC output voltage between 5.25V and 6V through software switch.

-Support for fixed speed function.

-Can be used with a variety of programmed card (Note: Optional) Use the programming card has a simple and intuitive interface, easy to you anywhere modify the various programming parameters (see set card manual).

-Through the USB interface the programmed card on the the ESC software upgrade, allows you to enjoy the latest ESC permanently.

-Full use of authentic materials to ensure that products with first-class quality and stable performance.

-Have complete independent intellectual property rights, sustainable updates.

Product Details:
-Product Model: Platinum-30A-Pro OPTO
-Weight: 31.6g
-Size: 56.5 * 25.6 * 8mm
-Continuous Current: 30A
-Instantaneous maximum current: 45A (10 sec.)
-BEC output: no
-The applicable number of battery cells :2-6S
-Nickel-metal hydride battery :5-18S
-Parameter programming function