This device allows you to safely and remotely kill your electronic ignition equipped engine your transmitter.igniton system is Fiber Optically Coupled to isolate your igniton system from your radio system .(No Interference!!)
This device features the following:
1. Includes a remote mountable bright LED to indicate when the ignition is armed.
2. Fiber Optic conpled input/output.
3. Pic12F675 Controller.
4. Li-Po/Li-lon/A123/Ni-Mh/NiCad Input.
5. Up to 20 Volt 16 amp MOS-FET(IRF7456) output.
6. Low to 3Volt 3amp output.
7. Low Voltage Drop-Less than 150mv.
8.100% Surface Mount Technology.
9. Heavy Gauge Wires,universal connectors.
10.Small and light weight ?Conly 0.3 OZ!(8g)
11.Reverse Bettery input protection.
12. Shut down the transmitter power or receiver to cut off automatically when
kill engine
This device plugs into a spare receiver channel
This is a must have safety device for any gas powered plane!
This device allows you to safely kill your engine at anytime (on the ground ,or in the air!)
Or when out of control also allows kill the enfine

AUSTARS RCEXL single ignition for Zenoah G38( Including 46#)BPMR6A

AUSTARS RCEXL M5*60mm Engine Mount 4pcs

Details:

Specifications:

² Suitable for Spark Plug: NGK CM6-10MM (not included)

² Working Voltage: 4.8-6V

² Interface Type: FUTABA (4pcs)

² Weight: 132g

Included Parts:

² CDI*1pcs

² 90 Degree Spark Plug Cap*1pcs

² Tight Pipe*1pcs

² Sensor Bracket

RCEXL 9 cylinder RADIAL ENGINE ignition for -NGK- ME-8 1/4 -32 CM-6--10MM

Specification:

Rcexl Ignition systems are designed and built for use with model airplane hobby use only, not for use in any type of man carrying vehicle. Large engine powered model airplanes are not toys. Keep children away and use extreme caution when flying or running engines.

RCEXL 5 cylinder RADIAL ENGINE ignition for -NGK- ME-8 1/4 -32 CM-6--10MM

Specification:

Rcexl Ignition systems are designed and built for use with model airplane hobby use only, not for use in any type of man carrying vehicle. Large engine powered model airplanes are not toys. Keep children away and use extreme caution when flying or running engines.

4 Cylinder Inline engine ignition for -NGK- ME-8 1/4 -32 90degree

Specification:

Rcexl Ignition systems are designed and built for use with model airplane hobby use only, not for use in any type of man carrying vehicle. Large engine powered model airplanes are not toys. Keep children away and use extreme caution when flying or running engines.

RCEXL 7 cylinder RADIAL ENGINE ignition for -NGK- ME-8 1/4 -32 CM-6--10MM

Specification:

Rcexl Ignition systems are designed and built for use with model airplane hobby use only, not for use in any type of man carrying vehicle. Large engine powered model airplanes are not toys. Keep children away and use extreme caution when flying or running engines.

AUSTARS RCEXL CM6 Spark Plug : Spark-CM6

AUSTARS RCEXL NGK CM6 Spark Plug : Spark-CM6

AUSTARS RCEXL Red Color Round Fuel Dot for airplane

Details:

Specifications:

² Working Voltage: 4.8V-8.4V

² Plug Type: Futaba Female (for Battery), Futaba Female (for Tachometer)

² Net Weight (CDI): 151g

² Suitable for Spark Plug: NGK-ME8 1/4-32

Package Contents:

² CDI Ignition*1pcs

² Contraction Duct*1pcs

² Spark Plug Cap*2pcs (NGK-ME8 1/4-32 Straight)

Details:

Specifications:

² Working Voltage: 4.8V-8.4V

² Plug Type: Futaba Female (for Battery), Futaba Female (for Tachometer)

² Net Weight (CDI): 157g

² Suitable for Spark Plug: CM6-10mm

Package Contents:

² CDI Ignition*1pcs

² Contraction Duct*1pcs

² Spark Plug Cap*2pcs (CM-6-10MM Straight)

Details:

Specifications:

² Working Voltage: 4.8V-8.4V

² Plug Type: Futaba Female (for Battery), Futaba Female (for Tachometer)

² Net Weight (CDI): 161g

² Suitable for Spark Plug: CM6-10mm

Package Contents:

² CDI Ignition*1pcs

² Contraction Duct*1pcs

² Spark Plug Cap*2pcs (CM-6-10MM 120 Degree)

Details:

Specifications:

² Working Voltage: 4.8V-8.4V

² Plug Type: Futaba Female (for Battery), Futaba Female (for Tachometer)

² Net Weight (CDI): 167g

² Suitable for Spark Plug: BPMR6F-14MM

Package Contents:

² CDI Ignition*1pcs

² Contraction Duct*1pcs

² Spark Plug Cap*2pcs (BPMR6F-14MM 90 Degree)

Details:

Specifications:

² Working Voltage: 4.8V-8.4V

² Plug Type: Futaba Female (for Battery), Futaba Female (for Tachometer)

² Net Weight (CDI): 172g

² Suitable for Spark Plug: BMR6A-14MM

Package Contents:

² CDI Ignition*1pcs

² Contraction Duct*1pcs

² Spark Plug Cap*2pcs (BMR6A-14MM 90 Degree)

Details:

Specifications:

² Working Voltage: 4.8V-8.4V

² Plug Type: Futaba Female (for Battery), Futaba Female (for Tachometer)

² Net Weight (CDI): 120g

² Suitable for Spark Plug: BMR6A-14MM

Package Contents:

² CDI Ignition*1pcs

² Contraction Duct*1pcs

² Spark Plug Cap*1pcs (BMR6A-14MM 90 Degree)

Details:

Specifications:

² Working Voltage: 4.8V-8.4V

² Plug Type: Futaba Female (for Battery), Futaba Female (for Tachometer)

² Net Weight (CDI): 120g

² Suitable for Spark Plug: BPMR6F-14MM

Package Contents:

² CDI Ignition*1pcs

² Contraction Duct*1pcs

² Spark Plug Cap*1pcs (BPMR6F-14MM 90 Degree)

Details:

Specifications:

² Working Voltage: 4.8V-8.4V

² Plug Type: Futaba Female (for Battery), Futaba Female (for Tachometer)

² Net Weight (CDI): 147g

² Suitable for Spark Plug: NGK-ME8 1/4-32

Package Contents:

² CDI Ignition*1pcs

² Contraction Duct*1pcs

² Spark Plug Cap*2pcs(NGK-ME8 1/4-32 90 degree)

Details:

Specifications:

² Suitable for Spark Plug: NGK-ME8, 1/4-32 (not included)

² Working Voltage: 4.8-6V

² Interface Type: FUTABA (4pcs)

² Weight: 176g

Included Parts:

² CDI*1pcs

² Tight Pipe*1pcs

² 90 Degree Spark Plug Cap*2pcs

² Sensor Bracket

Details:

Specifications:

² Working Voltage: 4.8V-8.4V

² Plug Type: Futaba Female (for Battery), Futaba Female (for Tachometer)

² Net Weight (CDI): 161g

² Suitable for Spark Plug: CM6-10mm

Package Contents:

² CDI Ignition*1pcs

² Contraction Duct*1pcs

² Spark Plug Cap*2pcs (CM6 10MM 90 Degree)

Details:

Specifications:

² Working Voltage: 4.8V-8.4V

² Plug Type: Futaba Female (for Battery), Futaba Female (for Tachometer)

² Net Weight (CDI): 149g

² Suitable for Spark Plug: NGK-ME8 1/4-32

Package Contents:

² CDI Ignition*1pcs

² Contraction Duct*1pcs

² Spark Plug Cap*2pcs(NGK-ME8 1/4-32 120 degree)

Details:

Specifications:

² Working Voltage: 4.8V-8.4V

² Plug Type: Futaba Female (for Battery), Futaba Female (for Tachometer)

² Net Weight (CDI): 114g

² Suitable for Spark Plug: CM6 10mm

Package Contents:

² CDI Ignition*1pcs

² Contraction Duct*1pcs

² Spark Plug Cap*1pcs (CM6 10MM 90 Degree)

Details:

Specifications:

² Working Voltage: 4.8V-8.4V

² Plug Type: Futaba Female (for Battery), Futaba Female (for Tachometer)

² Net Weight (CDI): 114g

² Suitable for Spark Plug: CM6-10mm

Package Contents:

² CDI Ignition*1pcs

² Contraction Duct*1pcs

² Spark Plug Cap*1pcs (CM6-10MM Straight)

Details:

Specifications:

² Working Voltage: 4.8V-8.4V

² Plug Type: Futaba Female (for Battery), Futaba Female (for Tachometer)

² Net Weight (CDI): 108g

² Suitable for Spark Plug: NGK-ME8 1/4-32

Package Contents:

² CDI Ignition*1pcs

² Contraction Duct*1pcs

² Spark Plug Cap*1pcs(NGK-ME8 1/4-32 120 degree)

Details:

Specifications:

² Working Voltage: 4.8V-8.4V

² Plug Type: Futaba Female (for Battery), Futaba Female (for Tachometer)

² Net Weight (CDI): 108g

² Suitable for Spark Plug: NGK-ME8 1/4-32

Package Contents:

² CDI Ignition*1pcs

² Contraction Duct*1pcs

² Spark Plug Cap*1pcs(NGK-ME8 1/4-32 90 degree)

Details:

Specifications:

² Suitable for Spark Plug: NGK-ME8, 1/4-32 (not included)

² Working Voltage: 4.8-6V

² Interface Type: FUTABA (4pcs)

² Weight: 125g

Included Parts:

² CDI*1pcs

² Tight Pipe*1pcs

² 90 Degree Spark Plug Cap*1pcs

² Sensor Bracket

Details:

Specifications:

² Working Voltage: 4.8V-8.4V

² Plug Type: Futaba Female (for Battery), Futaba Female (for Tachometer)

² Net Weight (CDI): 108g

² Suitable for Spark Plug: NGK-ME8 1/4-32

Package Contents:

² CDI Ignition*1pcs

² Contraction Duct*1pcs

² Spark Plug Cap*1pcs (NGK-ME8 1/4-32 Straight)

Details:

Specifications:

² Working Voltage: 4.8V-8.4V

² Plug Type: Futaba Female (for Battery), Futaba Female (for Tachometer)

² Net Weight (CDI): 224g

² Suitable for Spark Plug: NGK-CM-6-10MM

Package Contents:

² CDI Ignition*1pcs

² Contraction Duct*1pcs

² Spark Plug Cap*3pcs (NGK-CM6-10MM 120 Degree)

Details:

Specifications:

² Working Voltage: 4.8V-8.4V

² Plug Type: Futaba Female (for Battery), Futaba Female (for Tachometer)

² Net Weight (CDI): 204g

² Suitable for Spark Plug: NGK-ME8 1/4-32

Package Contents:

² CDI Ignition*1pcs

² Contraction Duct*1pcs

² Spark Plug Cap*3pcs (NGK-ME8 1/4-32 90 Degree)

Details:

Specifications:

² Working Voltage: 4.8V-8.4V

² Plug Type: Futaba Female (for Battery), Futaba Female (for Tachometer)

² Net Weight (CDI): 196g

² Suitable for Spark Plug: NGK-CM6-10MM

Package Contents:

² CDI Ignition*1pcs

² Contraction Duct*1pcs

² Spark Plug Cap*3pcs (NGK-CM6-10MM 90 Degree)

AUSTARS MIRACLE Propeller Drill Guide for DLE111 & 222

AUSTARS RCEXL The first Iridium Spark Plug for RC Model Engine in the world. Good Quality and Cheap Price!

Details:

Specifications:

² Suitable for Spark Plug: NGK -BPMR6A-14MM (not included)

² Working Voltage: 4.8-6V

² Interface Type: FUTABA (4pcs)

² Weight: 189g

Included Parts:

² CDI*1pcs

² Tight Pipe*1pcs

² 90 Degree Spark Plug Cap*2pcs

² Sensor Bracket

Details:

Specifications:

² Suitable for Spark Plug: NGK -BPMR6F-14MM (not included)

² Working Voltage: 4.8-6V

² Interface Type: FUTABA (4pcs)

² Weight: 186g

Included Parts:

² CDI*1pcs

² Tight Pipe*1pcs

² 90 Degree Spark Plug Cap*2pcs

² Sensor Bracket

Details:

Specifications:

² Working Voltage: 4.8V-8.4V

² Plug Type: Futaba Female (for Battery), Futaba Female (for Tachometer)

² Net Weight (CDI): 204g

² Suitable for Spark Plug: NGK-ME8 1/4-32

Package Contents:

² Hall Sensor Kits*1 set

² CDI Ignition*1pcs

² Contraction Duct*1pcs

² Spark Plug Cap*3pcs (NGK-ME8 1/4-32 120 Degree)

AUSTARS RCEXL Oil Drum Cap With Connector Whole set

AUSTARS RCEXL One Way Fuel Pipe Connector (for gas ) L38mm

AUSTARS RCEXL One Way Fuel Pipe Connector (General) L38mm

Specifications:
2 Input Voltage: 6-13V
2 Output Voltage: 4.8-9.6V( default voltage: 5.2V)
2 Output Current: 0-15A (Max. 20A)
2 Dimension: 65*27*35mm
2 Weight: 60g
Features:
Use high definition nixie tube, number will still clearly visible even in the sunshine.
Short for Onboard equipment, integration in electronic switch, voltage input and output display and large current UBEC.
Three-position nixie tube displays input and output voltage timely, assist you to get know the power supply status in the first time.
Output voltage: 4.8-9.6V, suitable for all kinds of high and low voltage servos and receivers in market.
Large output current: 15 A (MAX.20A), beneficial to provide continuous sufficient operating current for servo.
Working voltage: 6-13V, applicable to get power from Lipo, Ni-MH, Ni-Cd, A123 Li-Fe and other batteries directly.
If powered off suddenly while operating, it will keep outputting voltage normally when powered on.
Use Method:
Long press on red button for 2 seconds to start. (Indicator light shows long time, nixie tube prompts inputting voltage after 3 seconds; Indicator light flashes, nixie tube prompts outputting voltage after 3 seconds.)
Long press on red button for 2 seconds to turn off.
On state, short press on red button to switch to output voltage (red indicator light flashes); Short press on red button again to switch to input voltage (red indicator light shows); Voltage will calculatedly show if short press again.
If need to adjust the output voltage, short press on red button to switch to output voltage. Use a Straight screwdriver to adjust the potentiometer at the tail of the step-down transformer. Counterclockwise rotation for output voltage value decrease and clockwise rotation for output voltage value increase.
Kindly Remark
Battery negative and positive pole are not allowed to be connected in an opposite way.
Not allowed to be exposure to oil or water, even exposed to something corrosive when installation.
Pay attention to air ventilation when using large power.
Kindly suggest using high quality batteries to supply power, bad batteries will impact the stability of power supply and even lose control caused by power shortage.

AUSTARS RCEXL RCEXL 130CC-170CC Air Intake Horn Mouth CNC Aluminum Alloy for Petrol Engine
Specifications:

Material: Aluminum Alloy
Net Weight: 22g
Processing Pattern: Surface Oxidized after CNC processed
Function: Air Intake Horn Mouth has the effect of rectification and intension on the air intake of engine, which can improve accelerator s responsiveness and the highest rotating speed of the engine.
Suitable for Petrol Engines of displacement from 130CC to 170CC

AUSTARS MIRACLE High quality CNC Fuel plug-Black Color ( magnet inside)

Made of high rigidity aluminum alloy, the fuel filler with fuel dot can directly fill oil for the fuel tank without opening the canopy of boat and airplane.

AUSTARS MIRACLE High quality CNC Fuel plug-Black Color(magnet inside)

Made of high rigidity aluminum alloy, the fuel filler with fuel dot can directly fill oil for the fuel tank without opening the canopy of boat and airplane.

AUSTARS RCEXL RC Model Rcexl Ignition Medium Conversion Kit W/ Sensor Bracket for Zenoah Gas Engine G38

AUSTARS RCEXL RC Model Rcexl Ignition Small Conversion Kit W/ Sensor Bracket for Zenoah Gas Engine G26SC/ G26SLH/ G26SCM/ G26SLH

Opto Kill switch is a very useful device for RC petrol engine.This product is used to turn the remote petrol engine on or off. The remote control switch series with the CDI wire and the CDI power wire, you can use either channel to control your petrol engine (usually the on/off channel). This product can effectively protect yourself and the model plane being hurt from suddenness. In addition, this product has install an external large capacitor for receiver power with 4700UF, it can make the receiver voltage more stable, more pure, and improve the operation stability of electronic devices effectively. To a certain extent, it can eliminate the clutter interference and effective way to ease the voltage fluctuations which is coursed by multiple steering engines action at the same time.

Product Features:
1. Bi-color LED indicator light shows the current voltage status of your RX battery pack.
2. Retrofitting 4700UF large capacitor voltage can make the receiver more stable, pure.
3. Wide operating voltage can applied to lithium, nickel hydride, nickel cadmium, A123 and other battery-powered directly.
4. Can be used for other purposes, such as: pull the smoke detectors, retract or expand the landing gear, lighting fireworks and so on
5. The receiver and the CDI is completely separated, so you wouldn??t worry the receiver will be interfered by high frequency signal which is happen to CDI.
Petrol engine CDI remote control switch
weight:10g(include lead wire )
Size:33mm(length) x 13mm(wide) x 13mm(high)
Working current: 0~4A
working voltage: 3V~8V

Product Description:
The built-in nitro ignition is used for RC planes, RC cars and RC boats nitro engine.
CDI battery is no need to add, because the CDI can be connected to receiver battery
directly and can ignite by controlling the fifth channel on the remote control.
The buzzer phone will indicate the ignition condition

Specifications:
1. CDI Working Voltage: 4.2-6V, 4.2-12.6V (if receiver supports high voltage)
2. Voltage Display Range (Nixie tube): 3.5-15V
3. Max. Current (switch): 20A
4. Input Wire: 24# silicone wire, L15cm
5. Output Wire: 60 cores, L25cm
6. Plug Type: FUTABA/ JR compatible
7. CDI Wire: 24# silicone wire, L40cm
8. Weight: 50g

AUSTARS RCEXL Drill Jig Specially for MLD28 / MLD35 / MLD43 / MLD70

AUSTARS RCEXL Fuel Line For gas engine(??4.8*2.5) White Color 200meter/volume

Size:4.8*2.5mm
Outside diameter: 4.8mm
Inside diameter:2.5mm
Color: Yellow and blue both are in availble.

This is corrosion resistant fuel line.We have tested this gas line in 93# petrol more than 6 month,No Metamorphose.

Material: TPU

AUSTARS RCEXL Fuel Line for Nitro Engine (5*2.5) Red Color 200meter(656 ft)/volume

Size:5x2.5mm
Outside diameter: 5mm
Inside diameter:2.5mm
Color: Yellow.Red and White are in availible.

This is corrosion resistant fuel line.We have tested this Fuel line in Nitro Fuel more than 6 month, No Metamorphose.

Material: TPU

AUSTARS RCEXL Fuel Line For gas engine(10*6) White Color 100meter/volume

AUSTARS RCEXL Rcexl twin ignitions for CNGK- ME-8 ,1/4 -32 spark plug 120degree

Specifications:
Suitable for Spark Plug: NGK- ME-8, 1/4-32 (not included)
Working Voltage: 4.8-8.4V
Interface Type: FUTABA (4pcs)
Weight: 125g
Included Parts: 2 CDI*1pcs 2 Tight Pipe*1pcs 2 90 Degree Spark Plug Cap*1pcs 2 Sensor Bracket

pecifications:
Suitable for Spark Plug: NGK- ME-8, 1/4 -32 (not included)
Working Voltage: 4.8-8.4V
Interface Type: FUTABA (4pcs)
Weight: 125g
Included Parts:
CDI*1pcs
Tight Pipe*1pcs
120 Degree Spark Plug Cap*1pcs
Sensor Bracket

AUSTARS RCEXL Fuel Line for Nitro Engine (5*2.5) Yellow Color 200meter(656 ft) /volume

Size:5*2.5mm
Outside diameter: 5mm
Inside diameter:2.5mm
Color: Yellow Red and White are in availble.

This is corrosion resistant fuel line.We have tested this Fuel line in Nitro Fuel more than 6 months,No Metamorphose.

Material: TPU

AUSTARS RCEXL Fuel Line for Nitro Engine (5*2.5) White Color 200meter/volume

Size:5*2.5mm
Outside diameter: 5mm
Inside diameter:2.5mm
Color: Yellow Red and White are in availble.

This is corrosion resistant fuel line.We have tested this Fuel line in Nitro Fuel more than 6 months ,No Metamorphose.

Material: TPU

AUSTARS RCEXL Fuel Line For gas engine(6*3) Yellow Color 200meter/volume

AUSTARS RCEXL Fuel Line For gas engine(6*3) Blue Color 200meter(656 ft)/volume

Size:6*3mm
Outside diameter: 6mm
Inside diameter:3mm
Color: Yellow and blue both are in availble.

This is corrosion resistant fuel line.We have tested this gas line in 93# petrolmore than 6 months,No Metamorphose.

Material: TPU

AUSTARS RCEXL Fuel Line For gas engine(6*3) White Color 200meter/volume

Size:6*3mm
Outside diameter: 6mm
Inside diameter:3mm
Color: Yellow,White and blue color are in availble.

This is corrosion resistant fuel line.We have tested this gas line in 93# petrol more than 6 months ,No Metamorphose.

Material: TPU

AUSTARS RCEXL Fuel Line For gas engine(??4.8*2.5) Blue Color 200meter/volume

Size:4.8*2.5mm
Outside diameter: 4.8mm
Inside diameter:2.5mm
Color: Yellow and blue both are in availble.

This is corrosion resistant fuel line.We have tested this gas line in 93# petrol more than 6 month,No Metamorphose.

Material: TPU

AUSTARS RCEXL Fuel Line For gas engine(7*4) Blue Color 100meter/volume

AUSTARS RCEXL

Features:

Used to balance the propellers or blades with different sizes.
Aluminum alloy balance bar connected with four ball bearings, very smooth and precise.
Frame made of thickened organic glass, much solider.

Applications Fields:

Ducted Fan Balance
Propeller Balance
Main Blade Balance

AUSTARS RCEXL RCEXL Digital Wireless Mini Tachometer

Specification:
2 It looks fancy and compact in size. Very handy to use.
2 It measures 2-9 blades prop rpm.
2 Multiply the readout by 10 for final rpm reading, it shows 4 digitals in a 10-99.999 rpm range
2 It comes with a replaceable 3v LITHIUM battery.
2 There is an auto shut-off function after five minutes when no signal received.
2 Display and memorize the maximum rpm value.
2 It needs a little electronic power (20uA) when the tachometer is not in use. This depends on battery??s capacity for life of battery

AUSTARS RCEXL RCEXL 50pcs*Aluminum Clip for Steel Wire
Specifications: Clip
Material: aluminum This clip is designed for fastening the steel wire dragline with 0.8-1mm diameter.

AUSTARS RCEXL RCEXL Vibration Absorbers for YS 140~170

Specifications:

1. Dimension: d3
4.3*L71*D50 mm
2. Material: aluminum alloy (outside), with rubber ring inside.
3. Weight: 18.8g
4. Suitable for: YS engine 140-170 Class

AUSTARS RCEXL RCEXL Vibration Absorbers for YS 140~170

Specifications:
1. Dimension: d3
4.3*L71*D50 mm
2. Material: aluminum alloy (outside), with rubber ring inside.
3. Weight: 13.8g
4. Suitable for: YS engine 140-170 Class

AUSTARS RCEXLRCEXL Vibration Absorbers for YS 110

Specifications:
1. Dimension: d27*L60*D30mm
2. Material: aluminum alloy (outside), with rubber ring inside.
3. Weight: 6.5g
4. Suitable for: YS engine 110 Class

AUSTARS RCEXLRCEXL Triangle Vibration Absorbers for YS 110

Specifications:
1. Dimension: d25*L54*D35mm
2. Material: aluminum alloy (outside), with rubber ring inside.
3. Weight: 12g
4. Suitable for: YS engine 110 Class

AUSTARS RCEXL Propeller Reamer (Stepped for 5mm,1/4",5/16",3/8")

AUSTARS RCEXL Propeller Drill Guide for DLE111 & 222

AUSTARS RCEXL Propeller Balancer A

AUSTARS RCEXL RC Model Rcexl Ignition Large Conversion Kit W/ Sensor Bracket for Zenoah Gas Engine G45/ G62/ GT80

AUSTARS RCEXL Spark plug caps and boots for NGK -CM6-10MM

Technical parameters:
working voltage: 4.2 13V
operating current of the igniter:0-5A
output voltage of the igniter:1.5V
Weight: 20g
Volume: 35mm ( L ) * 17mm ( W) * 8mm ( H )

AUSTARS RCEXL Air filter for 20-60cc gas engine

AUSTARS RCEXL Aluminium Alloy Oil Drum Cap

Specifications:
Suitable for Spark Plug: NGK -BPMR6F-14MM (not included)
Working Voltage: 4.8-6V
Interface Type: FUTABA (4pcs)
Weight: 186g
Included Parts:
CDI*1pcs
Tight Pipe*1pcs
90 Degree Spark Plug Cap*2pcs
Sensor Bracket

Specifications:
Suitable for Spark Plug: NGK-BMR6A-14MM (not included)
Working Voltage: 4.8-6V
Interface Type: FUTABA (4pcs)
Weight: 135g
Included Parts:
CDI*1pcs
Tight Pipe*1pcs
90 Degree Spark Plug Cap*1pcs
Sensor Bracket

Specifications:
Suitable for Spark Plug: NGK CM6-10MM (not included)
Working Voltage: 4.8-6V
Interface Type: FUTABA (4pcs)
Weight: 132g
Included Parts:
CDI*1pcs
90 Degree Spark Plug Cap*1pcs
Tight Pipe*1pcs
Sensor Bracket