JP Hobby Multifunction CB-Retract Combined controller V1/V2 for ER-05/08/10/120/150/200 with Brake Module

Description

The main difference between the new Combined Retract Controller and the Integrated Retract Controller is that the Combined Retract Controller features three gear door channels, allows the setting of both V1 and V2 versions, and offers the ability to change the direction of the gear door servo.

Additionally, it supports all versions of the ER-005, ER-010, ER-120, ER-150, and ER-200 retract systems, automatically identifying the specific requirements of the landing gear.

• The functions of the JP Hobby module are multiple:
• Automatic detection of the supply voltage
• Adjusting the supply voltage of the servos actuating the gear doors
• Adjusting the direction of rotation of the servos actuating the gear doors
• Mode selection:

- 1: Opened gear doors when the landing gear is out
- 2: Closed gear doors when the landing gear is out

Specifications

• Dimensions: 52x37x14mm
• Entraxe: 64mm
• Voltage range: 7.4-8.4V
• Weight: 34.7g

Gear Door Controller Setup Instructions

This controller supports three gear door channels, each of which can be configured independently. You can adjust V1/V2 positions and servo directions (positive or negative) for each gear door.

Function 1: V1/V2 Position Setup

(V1: landing gears doors stay open - V2 : closed)

To enter the position setup mode:
1. Press and hold the Mode key for 5 seconds.
2. The red light indicates the controller is in V1 setup mode.
3. Press the Mode key again to switch to V2 mode, indicated by a blue light.

If the Mode key is not pressed within a few seconds, the controller will automatically move to the next channel.
Once all three channels have been configured, the system will automatically exit the setup mode.

Function 2: Servo Direction Setup

To configure the servo direction (positive or negative):
1. Press and hold the Mode key for 10 seconds to enter servo direction setup mode.
2. A red light indicates the positive direction, and a blue light indicates the negative direction.
(Note: In some models, this color assignment may be reversed.)

If the Mode key is not pressed, the system will automatically proceed to the next channel.
After all three channels have been set, the system will exit the setup mode automatically.

Compatibility

JP Hobby Bicycle Sequencer Retract Box ER-150 V1 Landing Gear with Break Module

This electronic switch is used to control the sequence of 2 electric retract from your transmitter gear channel switch. Also include a wheel brake module for JP Hobby. It is a replacement control box for the JP Hobby electric retracts.

This version equiped with a 2s plug is for use with the ER-150 retracts from JP Hobby.

Warning: Be care of using this sequencer for a 2 retracts landing gear only

Note : Version 2 closes the doors when the gear is down while version 1 keep the doors open.

WARNING: Servos which controlling the gear doors must imperatively be H.V. (High Voltage) type 

Specifications

• Input voltage: 7.4V to 8.4V (2 cells lipo)
• Size: 52 x 32 x 21 mm
• Weight: 50 gr

Compatibility

JP Hobby Bicycle Sequencer Retract Box ER-150 V1 Landing Gear with Break Module

This electronic switch is used to control the sequence of 2 electric retract from your transmitter gear channel switch. Also include a wheel brake module for JP Hobby. It is a replacement control box for the JP Hobby electric retracts.

This version equiped with a 2s plug is for use with the ER-150 retracts from JP Hobby.

Warning: Be care of using this sequencer for a 2 retracts landing gear only

Note : Version 2 closes the doors when the gear is down while version 1 keep the doors open.

WARNING: Servos which controlling the gear doors must imperatively be H.V. (High Voltage) type 

Specifications

• Input voltage: 7.4V to 8.4V (2 cells lipo)
• Size: 52 x 32 x 21 mm
• Weight: 50 gr

Compatibility

JP Hobby Multifunction Landing Gears and Doors Sequencer V1/V2 for ER-05/08/10/120/150/200

Description

This new JP Hobby electronic module is used to control the animation sequences of retractable landing gear as well as doors. It can also be used with other enclosures equipped with integrated end of limit switches.

The functions of the JP Hobby module are multiple:
Automatic detection of the supply voltage
Adjusting the supply voltage of the servos actuating the gear doors
Adjusting the direction of rotation of the servos actuating the gear doors
Mode selection:

- 1: Opened gear doors when the landing gear is out
- 2: Closed gear doors when the landing gear is out

This controller can be used for either bicycles or tricycles gears systems from JP Hooby.

Specifications

• Dimensions: 63x42x16mm
• Voltage range: 7.4-8.4V
• Weight: 34.7g

Compatibility

JP Hobby Tricycle Sequencer Retract Box ER-200 V2 Landing Gear with Break Module

This electronic switch is used to control the sequence of electric retract from your transmitter gear channel switch. Also include a wheel brake module for JP Hobby. It is a replacement control box for the JP Hobby electric retracts.

Note: Version 2 closes the doors when the gear is down while version 1 keep the doors open.

WARNING: Servos which controlling the gear doors must imperatively be H.V. (High Voltage) type 

Specifications

• Input voltage: 7.4V to 8.4V (2 cells lipo)
• Size: 52 x 31 x 22 mm
• Weight: 50 gr

Compatibility

JP Hobby Tricycle Sequencer Retract Box ER-200 V1 Landing Gear with Break Module

This electronic switch is used to control the sequence of electric retract from your transmitter gear channel switch. Also include a wheel brake module for JP Hobby. It is a replacement control box for the JP Hobby electric retracts.

Note: Version 2 closes the doors when the gear is down while version 1 keep the doors open. 

WARNING: Servos which controlling the gear doors must imperatively be H.V. (High Voltage) type 

Specifications

• Input voltage: 7.4V to 8.4V (2 cells lipo)
• Size: 52 x 31 x 22 mm
• Weight: 50 gr

JP Hobby Alloy Electric Motor Part type ER-200 M4 44mm

Specificities

• Weight: 68g
• Threaded shaft diameter : 4mm
• Threaded shaft lenght: 44mm
• Dimensions: cf pictures

Nota: Depending on the type of retract (retraction on the cylinder side or on the opposite side of the jack) the motor plug must be connected to the JP Hobby controller by observing the polarity (+ on + and - on -) or by reversing the polarities (+ on - and - on +) so as to reverse the retraction.

Warning: If you have connected the motor in the wrong direction, please immediately disconnect the controller motor or the power source, then reverse the motor plug on the controller and test again.

JP Hobby ER-150 Alloy Electric Retract Motor Part M4 47mm

Specificities

• Weight: 40g
• Threaded shaft diameter: 4mm
• Threaded shaft lenght: 47mm
• Dimensions: cf picture

Warning: If you have connected the motor in the wrong direction, please immediately disconnect the controller motor or the power source, then reverse the motor plug on the controller and test again.

JP Hobby ER-150 Alloy Electric Retract Motor Part M4 40mm

Specificities

• Weight: 40g
• Threaded shaft diameter: 4mm
• Threaded shaft lenght: 40mm
• Dimensions: cf picture

Nota: Depending on the type of retract (retraction on the cylinder side or on the opposite side of the jack) the motor plug must be connected to the JP Hobby controller by observing the polarity (+ on + and - on -) or by reversing the polarities (+ on - and - on +) so as to reverse the retraction.

Warning: If you have connected the motor in the wrong direction, please immediately disconnect the controller motor or the power source, then reverse the motor plug on the controller and test again.

JP Hobby Alloy Electric Motor Part type ER-150 M3 47mm

Specificities

• Weight: 40g
• Threaded shaft diameter : 3mm
• Threaded shaft lenght: 47mm
• Dimensions: cf picture

Nota: Depending on the type of retract (retraction on the cylinder side or on the opposite side of the jack) the motor plug must be connected to the JP Hobby controller by observing the polarity (+ on + and - on -) or by reversing the polarities (+ on - and - on +) so as to reverse the retraction.

Warning: If you have connected the motor in the wrong direction, please immediately disconnect the controller motor or the power source, then reverse the motor plug on the controller and test again.

JP Hobby Alloy Electric Motor Part type ER-150 M3 40mm

Specificities

• Weight: 40g
• Threaded shaft diameter : 3mm
• Threaded shaft lenght: 40mm
• Dimensions: cf picture

Nota: Depending on the type of retract (retraction on the cylinder side or on the opposite side of the jack) the motor plug must be connected to the JP Hobby controller by observing the polarity (+ on + and - on -) or by reversing the polarities (+ on - and - on +) so as to reverse the retraction.

Warning: If you have connected the motor in the wrong direction, please immediately disconnect the controller motor or the power source, then reverse the motor plug on the controller and test again.

JP Hobby Alloy Electric Motor Part type ER-120 M3 31mm

Specificities

• Weight: 24g
• Threaded shaft diameter : 3mm
• Threaded shaft lenght: 31mm
• Dimensions: cf pictures

Nota: Depending on the type of retract (retraction on the cylinder side or on the opposite side of the jack) the motor plug must be connected to the JP Hobby controller by observing the polarity (+ on + and - on -) or by reversing the polarities (+ on - and - on +) so as to reverse the retraction.

Warning: If you have connected the motor in the wrong direction, please immediately disconnect the controller motor or the power source, then reverse the motor plug on the controller and test again.

JP Hobby Alloy Electric Motor Part type ER-005 ER-008 M3 31mm

Specificities

• Weight: 19g
• Threaded shaft diameter : 3mm
• Threaded shaft lenght: 31mm
• Dimensions: cf pictures

Content

JP Hobby Bicycle Sequencer Retract Box ER-200 V2 Landing Gear with Break Module

This electronic switch is used to control the sequence of 2 electric retract from your transmitter gear channel switch. Also include a wheel brake module for JP Hobby. It is a replacement control box for the JP Hobby electric retracts.

This version equiped with a 2s plug is for use with the ER-200 retracts from JP Hobby.

Warning: Be care of using this sequencer for a 2 retracts landing gear only

Note : Version 2 closes the doors when the gear is down while version 1 keep the doors open.

WARNING: Servos which controlling the gear doors must imperatively be H.V. (High Voltage) type 

Specifications

• Input voltage: 7.4V to 8.4V (2 cells lipo)
• Size: 52 x 32 x 21 mm
• Weight: 32 gr

Compatibility

JP Hobby Bicycle Sequencer Retract Box ER-200 V1 Landing Gear with Break Module

This electronic switch is used to control the sequence of 2 electric retract from your transmitter gear channel switch. Also include a wheel brake module for JP Hobby. It is a replacement control box for the JP Hobby electric retracts.

This version equiped with a 2s plug is for use with the ER-200 retracts from JP Hobby.

Warning: Be care of using this sequencer for a 2 retracts landing gear only

Note : Version 2 closes the doors when the gear is down while version 1 keep the doors open.

WARNING: Servos which controlling the gear doors must imperatively be H.V. (High Voltage) type 

Specifications

• Input voltage: 7.4V to 8.4V (2 cells lipo)
• Size: 52 x 32 x 21 mm
• Weight: 32 gr

Compatibility

JP Hobby Bicycle Sequencer Retract Box ER-120 V2 Landing Gear with Break Module

This electronic switch is used to control the sequence of 2 electric retract from your transmitter gear channel switch. Also include a wheel brake module for JP Hobby. It is a replacement control box for the JP Hobby electric retracts.

This version equiped with a 2s plug is for use with the ER-120 retracts from JP Hobby.

Warning: Be care of using this sequencer for a 2 retracts landing gear only

Note : Version 2 closes the doors when the gear is down while version 1 keep the doors open.

WARNING: Servos which controlling the gear doors must imperatively be H.V. (High Voltage) type 

Specifications

• Input voltage: 7.4V to 8.4V (2 cells lipo)
• Size: 52 x 32 x 21 mm
• Weight: 50 gr

Compatibility

• JP Hobby retracts series ER-005, ER-010 et ER-120