This is the Austars Multi-Port Safe Parallel Adapter. This version supports LiPo batteries with JST XH compatible balance connectors and wiring. Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, and other charger brands compatible with JST XH balance connectors and wiring.

Features:

Support for safe parallel charging of up to 4 same-cell-count packs at one time (2s-8s)
Supports 40A max charge/discharge rate
Every port reverse polarity fuse protection of main battery wires
Every cell/balance wire protected by self-resetting polyfuses with temperature warning indicators
Supports non-balanced charge of up to two 1s LiPos used with "indoor models"

Supports 1 RX and 1 TX NiCd/NiMH battery pack. Works with any Cellpro charger or battery workstation equipped with XH wiring.

Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, as well as other brand chargers which are compatible with XH balance plugs and wiring. Be sure to purchase the proper cable to plug the MPA4 into your Charger or Battery Workstation

Parallel balance/charging board for 2-6s lithium polymer batteries with XT60 Connectors and JST-XH type balance connectors. You can use the parallel balance board to vastly reduce your charging time. For example if you have 3 of 2,200mAh 3s Li-Po batteries which you usually charge at 1C (2.2A), this would usually take approximately 3 hours to charge each pack individually. With this balance board you can charge all three packs in about one hour*.
This parallel balance board can be used to parallel charge and balance up to 6 lithium polymer batteries of the same cell count. We recommend that all cells should be within 0.1V of each other.
The balance connector from the board is a 6s JST-XH type. The charging lead from the board is standard 4mm charge leads, which should fit most chargers.
Maximum throughput, 40A. This board is fused.
Do not mix cell counts (i.e. do not try to parallel charge a 3s and 4s pack)
Do ensure that all cells are within 0.1V of each other before connecting
Do connect the main charge leads of the packs to the board before connecting the balance leads.

Features:

ABS Fireproof Material 2 oz PCB + Heavily Tinned 40A Fuse can be replaced Double insurance ( 4 Packs ParaBoard ) Super quality rc connectors High-end atmospheric grade Perfect design Quick-acting Charging Specification: 6 Packs paraBoard ( Fuse 40A ) 4 Packs paraBoard ( Fuse 40A + 1.85A / 1.1A ) Housing material : ABS Fireproof Material

Parallel balance/charging board for 2-6s lithium polymer batteries with XT60 Connectors and JST-XH type balance connectors. You can use the parallel balance board to vastly reduce your charging time. For example if you have 3 of 2,200mAh 3s Li-Po batteries which you usually charge at 1C (2.2A), this would usually take approximately 3 hours to charge each pack individually. With this balance board you can charge all three packs in about one hour.

This parallel balance board can be used to parallel charge and balance up to 6 lithium polymer batteries of the same cell count. We recommend that all cells should be within 0.1V of each other.
The balance connector from the board is a 6s JST-XH type. The charging lead from the board is standard 4mm charge leads, which should fit most chargers.
Maximum throughput, 40A. This board is fused.
Do not mix cell counts (i.e. do not try to parallel charge a 3s and 4s pack)
Do ensure that all cells are within 0.1V of each other before connecting
Do connect the main charge leads of the packs to the board before connecting the balance leads.

Features:

ABS Fireproof Material 2 oz PCB + Heavily Tinned 40A Fuse can be replaced Double insurance ( 4 Packs ParaBoard ) Super quality rc connectors High-end atmospheric grade Perfect design Quick-acting Charging
Specification: 6 Packs paraBoard ( Fuse 40A ) 4 Packs paraBoard ( Fuse 40A + 1.85A / 1.1A ) Housing material : ABS Fireproof Material Color : Black & Blue

New Austars ParaBoard is designed to be used in conjunction with a balance charger to simultaneously charge multiple lithium batteries in parallel. Using this method, you can significantly reduce the time required for charging multiple battery packs.

If your charger is capable of supplying enough charge current, you can charge 4 batteries in the time it would normally take to charge each battery individually. This means you can spend 1/4 as much time charging and more time flying!
The ParaBoard is made of high quality components. The PCB is made of two ounce copper and the main power circuit is heavily tinned to allow the use of high current. The boards have been individually tested under 25A continuous current, and they are safe to be loaded at 35A for shorter periods of time (10 Minutes Max)

Features:
Charges up to 4 packs in parallel
Expandable for more boards via the "Export" ports
Housing Material: ABS Fireproof Material

Specifications:
Balance Tap: JST-XH
Cell Count: 2-6s
Fuse: 40A (4 fuses)
Size: 152x76x17.5mm
Maximum continuous current: 25A
Maximum current for short term: 35A (10 Minutes Max)
Please follow all precautions included in manual before using this board for parallel charging. Not following these directions may result in fire and damages. Austars Model is not responsible for damaged batteries or property.
Batteries should ALWAYS be the same cell count
Batteries should ALWAYS have nearly the same voltage before charging
Never leave your charger unattended Keep away from flammable materials. Always connect balance taps before main power plugs when connecting to the board

New Austars ParaBoard is designed to be used in conjunction with a balance charger to simultaneously charge multiple lithium batteries in parallel. Using this method, you can significantly reduce the time required for charging multiple battery packs.
If your charger is capable of supplying enough charge current, you can charge 4 batteries in the time it would normally take to charge each battery individually. This means you can spend 1/4 as much time charging and more time flying!
The ParaBoard is made of high quality components. The PCB is made of two ounce copper and the main power circuit is heavily tinned to allow the use of high current. The boards have been individually tested under 25A continuous current, and they are safe to be loaded at 35A for shorter periods of time (10 Minutes Max)

Features:
Charges up to 4 packs in parallel
Expandable for more boards via the "Export" ports
Housing Material: ABS Fireproof Material

Specifications:
Balance Tap: JST-XH
Cell Count: 2-6s
Fuse: 40A (4 fuses)
Size: 152x76x17.5mm
Maximum continuous current: 25A
Maximum current for short term: 35A (10 Minutes Max)
Please follow all precautions included in manual before using this board for parallel charging. Not following these directions may result in fire and damages. Austars Model is not responsible for damaged batteries or property.
Batteries should ALWAYS be the same cell count
Batteries should ALWAYS have nearly the same voltage before charging
Never leave your charger unattended Keep away from flammable materials. Always connect balance taps before main power plugs when connecting to the board

New Austars ParaBoard is designed to be used in conjunction with a balance charger to simultaneously charge multiple lithium batteries in parallel. Using this method, you can significantly reduce the time required for charging multiple battery packs.

If your charger is capable of supplying enough charge current, you can charge 4 batteries in the time it would normally take to charge each battery individually. This means you can spend 1/4 as much time charging and more time flying!

The ParaBoard is made of high quality components. The PCB is made of two ounce copper and the main power circuit is heavily tinned to allow the use of high current. The boards have been individually tested under 25A continuous current, and they are safe to be loaded at 35A for shorter periods of time (10 Minutes Max)

Features:

Charges up to 4 packs in parallel
Expandable for more boards via the "Export" ports
Housing Material: ABS Fireproof Material

Specifications:
Balance Tap: JST-XH
Cell Count: 2-6s
Fuse: 40A (4 fuses)
Size: 152x76x17.5mm
Maximum continuous current: 25A
Maximum current for short term: 35A (10 Minutes Max)
Please follow all precautions included in manual before using this board for parallel charging. Not following these directions may result in fire and damages. Austars Model is not responsible for damaged batteries or property.
Batteries should ALWAYS be the same cell count
Batteries should ALWAYS have nearly the same voltage before charging
Never leave your charger unattended Keep away from flammable materials. Always connect balance taps before main power plugs when connecting to the board

New Austars ParaBoard is designed to be used in conjunction with a balance charger to simultaneously charge multiple lithium batteries in parallel. Using this method, you can significantly reduce the time required for charging multiple battery packs.

If your charger is capable of supplying enough charge current, you can charge 4 batteries in the time it would normally take to charge each battery individually. This means you can spend 1/4 as much time charging and more time flying!

The ParaBoard is made of high quality components. The PCB is made of two ounce copper and the main power circuit is heavily tinned to allow the use of high current. The boards have been individually tested under 25A continuous current, and they are safe to be loaded at 35A for shorter periods of time (10 Minutes Max)

Features:
Charges up to 4 packs in parallel
Expandable for more boards via the "Export" ports
Housing Material: ABS Fireproof Material

Specifications:
Balance Tap: JST-XH
Cell Count: 2-6s
Fuse: 40A (4 fuses)
Size: 152x76x17.5mm
Maximum continuous current: 25A
Maximum current for short term: 35A (10 Minutes Max)
Please follow all precautions included in manual before using this board for parallel charging. Not following these directions may result in fire and damages. Austars Model is not responsible for damaged batteries or property.
Batteries should ALWAYS be the same cell count
Batteries should ALWAYS have nearly the same voltage before charging
Never leave your charger unattended Keep away from flammable materials. Always connect balance taps before main power plugs when connecting to the board

Parallel balance/charging board for 2-6s lithium polymer batteries with XT60 Connectors and JST-XH type balance connectors. You can use the parallel balance board to vastly reduce your charging time. For example if you have 3 of 2,200mAh 3s Li-Po batteries which you usually charge at 1C (2.2A), this would usually take approximately 3 hours to charge each pack individually. With this balance board you can charge all three packs in about one hour.

This parallel balance board can be used to parallel charge and balance up to 6 lithium polymer batteries of the same cell count. We recommend that all cells should be within 0.1V of each other.
The balance connector from the board is a 6s JST-XH type. The charging lead from the board is standard 4mm charge leads, which should fit most chargers.
Maximum throughput, 40A. This board is fused.
Do not mix cell counts (i.e. do not try to parallel charge a 3s and 4s pack)
Do ensure that all cells are within 0.1V of each other before connecting
Do connect the main charge leads of the packs to the board before connecting the balance leads.

Features:

ABS Fireproof Material 2 oz PCB + Heavily Tinned 40A Fuse can be replaced Double insurance ( 4 Packs ParaBoard ) Super quality rc connectors High-end atmospheric grade Perfect design Quick-acting Charging
Specification: 6 Packs paraBoard ( Fuse 40A ) 4 Packs paraBoard ( Fuse 40A + 1.85A / 1.1A ) Housing material : ABS Fireproof Material Color : Black & Blue

Parallel balance/charging board for 2-6s lithium polymer batteries with XT60 Connectors and JST-XH type balance connectors. You can use the parallel balance board to vastly reduce your charging time. For example if you have 3 of 2,200mAh 3s Li-Po batteries which you usually charge at 1C (2.2A), this would usually take approximately 3 hours to charge each pack individually. With this balance board you can charge all three packs in about one hour.

This parallel balance board can be used to parallel charge and balance up to 6 lithium polymer batteries of the same cell count. We recommend that all cells should be within 0.1V of each other.
The balance connector from the board is a 6s JST-XH type. The charging lead from the board is standard 4mm charge leads, which should fit most chargers.
Maximum throughput, 40A. This board is fused.
Do not mix cell counts (i.e. do not try to parallel charge a 3s and 4s pack)
Do ensure that all cells are within 0.1V of each other before connecting
Do connect the main charge leads of the packs to the board before connecting the balance leads.

Features:

ABS Fireproof Material 2 oz PCB + Heavily Tinned 40A Fuse can be replaced Double insurance ( 4 Packs ParaBoard ) Super quality rc connectors High-end atmospheric grade Perfect design Quick-acting Charging
Specification: 6 Packs paraBoard ( Fuse 40A ) 4 Packs paraBoard ( Fuse 40A + 1.85A / 1.1A ) Housing material : ABS Fireproof Material Color : Black & Blue

Parallel balance/charging board for 2-6s lithium polymer batteries with XT60 Connectors and JST-XH type balance connectors. You can use the parallel balance board to vastly reduce your charging time. For example if you have 3 of 2,200mAh 3s Li-Po batteries which you usually charge at 1C (2.2A), this would usually take approximately 3 hours to charge each pack individually. With this balance board you can charge all three packs in about one hour*.
This parallel balance board can be used to parallel charge and balance up to 6 lithium polymer batteries of the same cell count. We recommend that all cells should be within 0.1V of each other.
The balance connector from the board is a 6s JST-XH type. The charging lead from the board is standard 4mm charge leads, which should fit most chargers.
Maximum throughput, 40A. This board is fused.
Do not mix cell counts (i.e. do not try to parallel charge a 3s and 4s pack)
Do ensure that all cells are within 0.1V of each other before connecting
Do connect the main charge leads of the packs to the board before connecting the balance leads.

Features:

ABS Fireproof Material 2 oz PCB + Heavily Tinned 40A Fuse can be replaced Double insurance ( 4 Packs ParaBoard ) Super quality rc connectors High-end atmospheric grade Perfect design Quick-acting Charging Specification: 6 Packs paraBoard ( Fuse 40A ) 4 Packs paraBoard ( Fuse 40A + 1.85A / 1.1A ) Housing material : ABS Fireproof Material

Parallel balance/charging board for 2-6s lithium polymer batteries with XT60 Connectors and JST-XH type balance connectors. You can use the parallel balance board to vastly reduce your charging time. For example if you have 3 of 2,200mAh 3s Li-Po batteries which you usually charge at 1C (2.2A), this would usually take approximately 3 hours to charge each pack individually. With this balance board you can charge all three packs in about one hour.

This parallel balance board can be used to parallel charge and balance up to 6 lithium polymer batteries of the same cell count. We recommend that all cells should be within 0.1V of each other.
The balance connector from the board is a 6s JST-XH type. The charging lead from the board is standard 4mm charge leads, which should fit most chargers.
Maximum throughput, 40A. This board is fused.
Do not mix cell counts (i.e. do not try to parallel charge a 3s and 4s pack)
Do ensure that all cells are within 0.1V of each other before connecting
Do connect the main charge leads of the packs to the board before connecting the balance leads.

Features:ABS Fireproof Material 2 oz PCB + Heavily Tinned 40A Fuse can be replaced Double insurance ( 4 Packs ParaBoard ) Super quality rc connectors High-end atmospheric grade Perfect design Quick-acting Charging
Specification: 6 Packs paraBoard ( Fuse 40A ) 4 Packs paraBoard ( Fuse 40A + 1.85A / 1.1A ) Housing material : ABS Fireproof Material Color : Black & Blue

New Austars ParaBoard is designed to be used in conjunction with a balance charger to simultaneously charge multiple lithium batteries in parallel. Using this method, you can significantly reduce the time required for charging multiple battery packs.
If your charger is capable of supplying enough charge current, you can charge 4 batteries in the time it would normally take to charge each battery individually. This means you can spend 1/4 as much time charging and more time flying!
The ParaBoard is made of high quality components. The PCB is made of two ounce copper and the main power circuit is heavily tinned to allow the use of high current. The boards have been individually tested under 25A continuous current, and they are safe to be loaded at 35A for shorter periods of time (10 Minutes Max)

Features:
Charges up to 4 packs in parallel
Expandable for more boards via the "Export" ports
Housing Material: ABS Fireproof Material

Specifications:
Balance Tap: JST-XH
?Cell Count: 2-6s
Fuse: 40A (4 fuses)
Size: 152x76x17.5mm
Maximum continuous current: 25A
Maximum current for short term: 35A (10 Minutes Max)
Please follow all precautions included in manual before using this board for parallel charging. Not following these directions may result in fire and damages. Austars Model is not responsible for damaged batteries or property.
Batteries should ALWAYS be the same cell count
Batteries should ALWAYS have nearly the same voltage before charging
Never leave your charger unattended Keep away from flammable materials. Always connect balance taps before main power plugs when connecting to the board

This is the Austars Multi-Port Safe Parallel Adapter. This version supports LiPo batteries with JST XH compatible balance connectors and wiring. Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, and other charger brands compatible with JST XH balance connectors and wiring.

Features:
Support for safe parallel charging of up to 4 same-cell-count packs at one time (2s-8s)
Supports 40A max charge/discharge rate
Every port reverse polarity fuse protection of main battery wires
Every cell/balance wire protected by self-resetting polyfuses with temperature warning indicators
Supports non-balanced charge of up to two 1s LiPos used with "indoor models"
Supports 1 RX and 1 TX NiCd/NiMH battery pack. Works with any Cellpro charger or battery workstation equipped with XH wiring.
Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, as well as other brand chargers which are compatible with XH balance plugs and wiring. Be sure to purchase the proper cable to plug the MPA4 into your Charger or Battery Workstation

This is the Austars Multi-Port Safe Parallel Adapter. This version supports LiPo batteries with JST XH compatible balance connectors and wiring. Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, and other charger brands compatible with JST XH balance connectors and wiring.

Features:
Support for safe parallel charging of up to 4 same-cell-count packs at one time (2s-8s)
Supports 40A max charge/discharge rate
Every port reverse polarity fuse protection of main battery wires
Every cell/balance wire protected by self-resetting polyfuses with temperature warning indicators
Supports non-balanced charge of up to two 1s LiPos used with "indoor models"
Supports 1 RX and 1 TX NiCd/NiMH battery pack. Works with any Cellpro charger or battery workstation equipped with XH wiring.
Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, as well as other brand chargers which are compatible with XH balance plugs and wiring. Be sure to purchase the proper cable to plug the MPA4 into your Charger or Battery Workstation

This is the Austars Multi-Port Safe Parallel Adapter. This version supports LiPo batteries with JST XH compatible balance connectors and wiring. Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, and other charger brands compatible with JST XH balance connectors and wiring.

Features:
Support for safe parallel charging of up to 4 same-cell-count packs at one time (2s-8s)

Supports 40A max charge/discharge rate
Every port reverse polarity fuse protection of main battery wires
Every cell/balance wire protected by self-resetting polyfuses with temperature warning indicators
Supports non-balanced charge of up to two 1s LiPos used with "indoor models"
Supports 1 RX and 1 TX NiCd/NiMH battery pack. Works with any Cellpro charger or battery workstation equipped with XH wiring.

Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, as well as other brand chargers which are compatible with XH balance plugs and wiring. Be sure to purchase the proper cable to plug the MPA4 into your Charger or Battery Workstation

This is the Austars Multi-Port Safe Parallel Adapter. This version supports LiPo batteries with JST XH compatible balance connectors and wiring. Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, and other charger brands compatible with JST XH balance connectors and wiring.

Features:
Support for safe parallel charging of up to 4 same-cell-count packs at one time (2s-8s)
Supports 40A max charge/discharge rate
Every port reverse polarity fuse protection of main battery wires
Every cell/balance wire protected by self-resetting polyfuses with temperature warning indicators
Supports non-balanced charge of up to two 1s LiPos used with "indoor models"
Supports 1 RX and 1 TX NiCd/NiMH battery pack. Works with any Cellpro charger or battery workstation equipped with XH wiring.
Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, as well as other brand chargers which are compatible with XH balance plugs and wiring. Be sure to purchase the proper cable to plug the MPA4 into your Charger or Battery Workstation

This is the Austars Multi-Port Safe Parallel Adapter. This version supports LiPo batteries with JST XH compatible balance connectors and wiring. Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, and other charger brands compatible with JST XH balance connectors and wiring.

Features:

Support for safe parallel charging of up to 4 same-cell-count packs at one time (2s-8s)
Supports 40A max charge/discharge rate
Every port reverse polarity fuse protection of main battery wires
Every cell/balance wire protected by self-resetting polyfuses with temperature warning indicators
Supports non-balanced charge of up to two 1s LiPos used with "indoor models"
Supports 1 RX and 1 TX NiCd/NiMH battery pack. Works with any Cellpro charger or battery workstation equipped with XH wiring.
Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, as well as other brand chargers which are compatible with XH balance plugs and wiring. Be sure to purchase the proper cable to plug the MPA4 into your Charger or Battery Workstation

This is the Austars Multi-Port Safe Parallel Adapter. This version supports LiPo batteries with JST XH compatible balance connectors and wiring. Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, and other charger brands compatible with JST XH balance connectors and wiring.

We had compared this one with few other brands on the market (4 Ports). The quality and materials used are better.

Features:
Support for safe parallel charging of up to 4 same-cell-count packs at one time (2s-8s)
Supports 40A max charge/discharge rate
Every port reverse polarity fuse protection of main battery wires
Every cell/balance wire protected by self-resetting polyfuses with temperature warning indicators
Supports non-balanced charge of up to two 1s LiPos used with "indoor models"
Supports 1 RX and 1 TX NiCd/NiMH battery pack. Works with any Cellpro charger or battery workstation equipped with XH wiring.? Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, as well as other brand chargers which are compatible with XH balance plugs and wiring. Be sure to purchase the proper cable to plug the MPA4 into your Charger or Battery Workstation

This is the Austars Multi-Port Safe Parallel Adapter. This version supports LiPo batteries with JST XH compatible balance connectors and wiring. Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, and other charger brands compatible with JST XH balance connectors and wiring.

We had compared this one with few other brands on the market (4 Ports). The quality and materials used are better.

Features:
Support for safe parallel charging of up to 4 same-cell-count packs at one time (2s-8s)
Supports 40A max charge/discharge rate
Every port reverse polarity fuse protection of main battery wires
Every cell/balance wire protected by self-resetting polyfuses with temperature warning indicators
Supports non-balanced charge of up to two 1s LiPos used with "indoor models"
Supports 1 RX and 1 TX NiCd/NiMH battery pack. Works with any Cellpro charger or battery workstation equipped with XH wiring.? Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, as well as other brand chargers which are compatible with XH balance plugs and wiring. Be sure to purchase the proper cable to plug the MPA4 into your Charger or Battery Workstation

New Austars ParaBoard is designed to be used in conjunction with a balance charger to simultaneously charge multiple lithium batteries in parallel. Using this method, you can significantly reduce the time required for charging multiple battery packs.
If your charger is capable of supplying enough charge current, you can charge 4 batteries in the time it would normally take to charge each battery individually. This means you can spend 1/4 as much time charging and more time flying!
The ParaBoard is made of high quality components. The PCB is made of two ounce copper and the main power circuit is heavily tinned to allow the use of high current. The boards have been individually tested under 25A continuous current, and they are safe to be loaded at 35A for shorter periods of time (10 Minutes Max)

Features:
Charges up to 4 packs in parallel
Expandable for more boards via the "Export" ports
Housing Material: ABS Fireproof Material

Specifications:
Balance Tap: JST-XH
Cell Count: 2-6s
Fuse: 40A (4 fuses)
Size: 152x76x17.5mm
Maximum continuous current: 25A
Maximum current for short term: 35A (10 Minutes Max)
Please follow all precautions included in manual before using this board for parallel charging. Not following these directions may result in fire and damages. Austars Model is not responsible for damaged batteries or property.
Batteries should ALWAYS be the same cell count
Batteries should ALWAYS have nearly the same voltage before charging
Never leave your charger unattended
Keep away from flammable materials Always connect balance taps before main power plugs when connecting to the board.

New Austars ParaBoard is designed to be used in conjunction with a balance charger to simultaneously charge multiple lithium batteries in parallel. Using this method, you can significantly reduce the time required for charging multiple battery packs.

If your charger is capable of supplying enough charge current, you can charge 4 batteries in the time it would normally take to charge each battery individually. This means you can spend 1/4 as much time charging and more time flying!

The ParaBoard is made of high quality components. The PCB is made of two ounce copper and the main power circuit is heavily tinned to allow the use of high current. The boards have been individually tested under 25A continuous current, and they are safe to be loaded at 35A for shorter periods of time (10 Minutes Max)

Features:

Charges up to 4 packs in parallel
Expandable for more boards via the "Export" ports
Housing Material: ABS Fireproof Material

Specifications:
Balance Tap: JST-XH
Cell Count: 2-6s
Fuse: 40A (4 fuses)
Size: 152x76x17.5mm
Maximum continuous current: 25A
Maximum current for short term: 35A (10 Minutes Max)
Please follow all precautions included in manual before using this board for parallel charging. Not following these directions may result in fire and damages. Austars Model is not responsible for damaged batteries or property.
Batteries should ALWAYS be the same cell count
Batteries should ALWAYS have nearly the same voltage before charging
Never leave your charger unattended Keep away from flammable materials. Always connect balance taps before main power plugs when connecting to the board

New Austars ParaBoard is designed to be used in conjunction with a balance charger to simultaneously charge multiple lithium batteries in parallel. Using this method, you can significantly reduce the time required for charging multiple battery packs.
If your charger is capable of supplying enough charge current, you can charge 4 batteries in the time it would normally take to charge each battery individually. This means you can spend 1/4 as much time charging and more time flying!
The ParaBoard is made of high quality components. The PCB is made of two ounce copper and the main power circuit is heavily tinned to allow the use of high current. The boards have been individually tested under 25A continuous current, and they are safe to be loaded at 35A for shorter periods of time (10 Minutes Max)

Features:
Charges up to 4 packs in parallel
Expandable for more boards via the "Export" ports
Housing Material: ABS Fireproof Material

Specifications:
Balance Tap: JST-XH
Cell Count: 2-6s
Fuse: 40A (4 fuses)
Size: 152x76x17.5mm
Maximum continuous current: 25A
Maximum current for short term: 35A (10 Minutes Max)
Please follow all precautions included in manual before using this board for parallel charging. Not following these directions may result in fire and damages. Austars Model is not responsible for damaged batteries or property.
Batteries should ALWAYS be the same cell count
Batteries should ALWAYS have nearly the same voltage before charging
Never leave your charger unattended
Keep away from flammable materials Always connect balance taps before main power plugs when connecting to the board.

Parallel balance/charging board for 2-6s lithium polymer batteries with XT60 Connectors and JST-XH type balance connectors. You can use the parallel balance board to vastly reduce your charging time. For example if you have 3 of 2,200mAh 3s Li-Po batteries which you usually charge at 1C (2.2A), this would usually take approximately 3 hours to charge each pack individually. With this balance board you can charge all three packs in about one hour.

This parallel balance board can be used to parallel charge and balance up to 6 lithium polymer batteries of the same cell count. We recommend that all cells should be within 0.1V of each other.
The balance connector from the board is a 6s JST-XH type. The charging lead from the board is standard 4mm charge leads, which should fit most chargers.
Maximum throughput, 40A. This board is fused.
Do not mix cell counts (i.e. do not try to parallel charge a 3s and 4s pack)
Do ensure that all cells are within 0.1V of each other before connecting
Do connect the main charge leads of the packs to the board before connecting the balance leads.

Features:ABS Fireproof Material 2 oz PCB + Heavily Tinned 40A Fuse can be replaced Double insurance ( 4 Packs ParaBoard ) Super quality rc connectors High-end atmospheric grade Perfect design Quick-acting Charging
Specification: 6 Packs paraBoard ( Fuse 40A ) 4 Packs paraBoard ( Fuse 40A + 1.85A / 1.1A ) Housing material : ABS Fireproof Material Color : Black & Blue

New Austars ParaBoard is designed to be used in conjunction with a balance charger to simultaneously charge multiple lithium batteries in parallel. Using this method, you can significantly reduce the time required for charging multiple battery packs.

If your charger is capable of supplying enough charge current, you can charge 4 batteries in the time it would normally take to charge each battery individually. This means you can spend 1/4 as much time charging and more time flying!

The ParaBoard is made of high quality components. The PCB is made of two ounce copper and the main power circuit is heavily tinned to allow the use of high current. The boards have been individually tested under 25A continuous current, and they are safe to be loaded at 35A for shorter periods of time (10 Minutes Max)

Features:
Charges up to 4 packs in parallel
Expandable for more boards via the "Export" ports
Housing Material: ABS Fireproof Material

Specifications:
Balance Tap: JST-XH
Cell Count: 2-6s
Fuse: 40A (4 fuses)
Size: 152x76x17.5mm
Maximum continuous current: 25A
Maximum current for short term: 35A (10 Minutes Max)
Please follow all precautions included in manual before using this board for parallel charging. Not following these directions may result in fire and damages. Austars Model is not responsible for damaged batteries or property.
Batteries should ALWAYS be the same cell count
Batteries should ALWAYS have nearly the same voltage before charging
Never leave your charger unattended Keep away from flammable materials. Always connect balance taps before main power plugs when connecting to the board

New Austars ParaBoard is designed to be used in conjunction with a balance charger to simultaneously charge multiple lithium batteries in parallel. Using this method, you can significantly reduce the time required for charging multiple battery packs.

If your charger is capable of supplying enough charge current, you can charge 4 batteries in the time it would normally take to charge each battery individually. This means you can spend 1/4 as much time charging and more time flying!

The ParaBoard is made of high quality components. The PCB is made of two ounce copper and the main power circuit is heavily tinned to allow the use of high current. The boards have been individually tested under 25A continuous current, and they are safe to be loaded at 35A for shorter periods of time (10 Minutes Max)

Features:
Charges up to 4 packs in parallel
Expandable for more boards via the "Export" ports
Housing Material: ABS Fireproof Material

Specifications:
Balance Tap: JST-XH
Cell Count: 2-6s
Fuse: 40A (4 fuses)
Size: 152x76x17.5mm
Maximum continuous current: 25A
Maximum current for short term: 35A (10 Minutes Max)
Please follow all precautions included in manual before using this board for parallel charging. Not following these directions may result in fire and damages. Austars Model is not responsible for damaged batteries or property.
Batteries should ALWAYS be the same cell count
Batteries should ALWAYS have nearly the same voltage before charging
Never leave your charger unattended Keep away from flammable materials.Always connect balance taps before main power plugs when connecting to the board

New Austars ParaBoard is designed to be used in conjunction with a balance charger to simultaneously charge multiple lithium batteries in parallel. Using this method, you can significantly reduce the time required for charging multiple battery packs.

If your charger is capable of supplying enough charge current, you can charge 4 batteries in the time it would normally take to charge each battery individually. This means you can spend 1/4 as much time charging and more time flying!

The ParaBoard is made of high quality components. The PCB is made of two ounce copper and the main power circuit is heavily tinned to allow the use of high current. The boards have been individually tested under 25A continuous current, and they are safe to be loaded at 35A for shorter periods of time (10 Minutes Max)

Features:
Charges up to 4 packs in parallel
Expandable for more boards via the "Export" ports
Housing Material: ABS Fireproof Material

Specifications:
Balance Tap: JST-XH
Cell Count: 2-6s
Fuse: 40A (4 fuses)
Size: 152x76x17.5mm
Maximum continuous current: 25A
Maximum current for short term: 35A (10 Minutes Max)
Please follow all precautions included in manual before using this board for parallel charging. Not following these directions may result in fire and damages. Austars Model is not responsible for damaged batteries or property.
Batteries should ALWAYS be the same cell count
Batteries should ALWAYS have nearly the same voltage before charging
Never leave your charger unattended Keep away from flammable materials. Always connect balance taps before main power plugs when connecting to the board

New Austars ParaBoard is designed to be used in conjunction with a balance charger to simultaneously charge multiple lithium batteries in parallel. Using this method, you can significantly reduce the time required for charging multiple battery packs.

If your charger is capable of supplying enough charge current, you can charge 4 batteries in the time it would normally take to charge each battery individually. This means you can spend 1/4 as much time charging and more time flying!
The ParaBoard is made of high quality components. The PCB is made of two ounce copper and the main power circuit is heavily tinned to allow the use of high current. The boards have been individually tested under 25A continuous current, and they are safe to be loaded at 35A for shorter periods of time (10 Minutes Max)

Features:
Charges up to 4 packs in parallel
Expandable for more boards via the "Export" ports
Housing Material: ABS Fireproof Material

Specifications:
Balance Tap: JST-XH
Cell Count: 2-6s
Fuse: 40A (4 fuses)
Size: 152x76x17.5mm
Maximum continuous current: 25A
Maximum current for short term: 35A (10 Minutes Max)
Please follow all precautions included in manual before using this board for parallel charging. Not following these directions may result in fire and damages. Austars Model is not responsible for damaged batteries or property.
Batteries should ALWAYS be the same cell count
Batteries should ALWAYS have nearly the same voltage before charging
Never leave your charger unattended Keep away from flammable materials. Always connect balance taps before main power plugs when connecting to the board

New Austars ParaBoard is designed to be used in conjunction with a balance charger to simultaneously charge multiple lithium batteries in parallel. Using this method, you can significantly reduce the time required for charging multiple battery packs.

If your charger is capable of supplying enough charge current, you can charge 4 batteries in the time it would normally take to charge each battery individually. This means you can spend 1/4 as much time charging and more time flying!
The ParaBoard is made of high quality components. The PCB is made of two ounce copper and the main power circuit is heavily tinned to allow the use of high current. The boards have been individually tested under 25A continuous current, and they are safe to be loaded at 35A for shorter periods of time (10 Minutes Max)

Features:
Charges up to 4 packs in parallel
Expandable for more boards via the "Export" ports
Housing Material: ABS Fireproof Material

Specifications:
Balance Tap: JST-XH
Cell Count: 2-6s
Fuse: 40A (4 fuses)
Size: 152x76x17.5mm
Maximum continuous current: 25A
Maximum current for short term: 35A (10 Minutes Max)
Please follow all precautions included in manual before using this board for parallel charging. Not following these directions may result in fire and damages. Austars Model is not responsible for damaged batteries or property.
Batteries should ALWAYS be the same cell count
Batteries should ALWAYS have nearly the same voltage before charging
Never leave your charger unattended Keep away from flammable materials. Always connect balance taps before main power plugs when connecting to the board

New Austars ParaBoard is designed to be used in conjunction with a balance charger to simultaneously charge multiple lithium batteries in parallel. Using this method, you can significantly reduce the time required for charging multiple battery packs.
If your charger is capable of supplying enough charge current, you can charge 4 batteries in the time it would normally take to charge each battery individually. This means you can spend 1/4 as much time charging and more time flying!
The ParaBoard is made of high quality components. The PCB is made of two ounce copper and the main power circuit is heavily tinned to allow the use of high current. The boards have been individually tested under 25A continuous current, and they are safe to be loaded at 35A for shorter periods of time (10 Minutes Max)

Features:
Charges up to 4 packs in parallel
Expandable for more boards via the "Export" ports
Housing Material: ABS Fireproof Material

Specifications:
Balance Tap: JST-XH
Cell Count: 2-6s
Fuse: 40A (4 fuses)
Size: 152x76x17.5mm
Maximum continuous current: 25A
Maximum current for short term: 35A (10 Minutes Max)
Please follow all precautions included in manual before using this board for parallel charging. Not following these directions may result in fire and damages. Austars Model is not responsible for damaged batteries or property.
Batteries should ALWAYS be the same cell count
Batteries should ALWAYS have nearly the same voltage before charging
Never leave your charger unattended Keep away from flammable materials. Always connect balance taps before main power plugs when connecting to the board

New Austars ParaBoard is designed to be used in conjunction with a balance charger to simultaneously charge multiple lithium batteries in parallel. Using this method, you can significantly reduce the time required for charging multiple battery packs.
If your charger is capable of supplying enough charge current, you can charge 4 batteries in the time it would normally take to charge each battery individually. This means you can spend 1/4 as much time charging and more time flying!
The ParaBoard is made of high quality components. The PCB is made of two ounce copper and the main power circuit is heavily tinned to allow the use of high current. The boards have been individually tested under 25A continuous current, and they are safe to be loaded at 35A for shorter periods of time (10 Minutes Max)

Features:
Charges up to 4 packs in parallel
Expandable for more boards via the "Export" ports
Housing Material: ABS Fireproof Material

Specifications:
Balance Tap: JST-XH
Cell Count: 2-6s
Fuse: 40A (4 fuses)
Size: 152x76x17.5mm
Maximum continuous current: 25A
Maximum current for short term: 35A (10 Minutes Max)
Please follow all precautions included in manual before using this board for parallel charging. Not following these directions may result in fire and damages. Austars Model is not responsible for damaged batteries or property.
Batteries should ALWAYS be the same cell count
Batteries should ALWAYS have nearly the same voltage before charging
Never leave your charger unattended Keep away from flammable materials. Always connect balance taps before main power plugs when connecting to the board

New Austars ParaBoard is designed to be used in conjunction with a balance charger to simultaneously charge multiple lithium batteries in parallel. Using this method, you can significantly reduce the time required for charging multiple battery packs.

If your charger is capable of supplying enough charge current, you can charge 4 batteries in the time it would normally take to charge each battery individually. This means you can spend 1/4 as much time charging and more time flying!
The ParaBoard is made of high quality components. The PCB is made of two ounce copper and the main power circuit is heavily tinned to allow the use of high current. The boards have been individually tested under 25A continuous current, and they are safe to be loaded at 35A for shorter periods of time (10 Minutes Max)

Features:
Charges up to 4 packs in parallel
Expandable for more boards via the "Export" ports
Housing Material: ABS Fireproof Material

Specifications:
Balance Tap: JST-XH
Cell Count: 2-6s
Fuse: 40A (4 fuses)
Size: 152x76x17.5mm
Maximum continuous current: 25A
Maximum current for short term: 35A (10 Minutes Max)
Please follow all precautions included in manual before using this board for parallel charging. Not following these directions may result in fire and damages. Austars Model is not responsible for damaged batteries or property.
Batteries should ALWAYS be the same cell count
Batteries should ALWAYS have nearly the same voltage before charging
Never leave your charger unattended Keep away from flammable materials. Always connect balance taps before main power plugs when connecting to the board

New Austars ParaBoard is designed to be used in conjunction with a balance charger to simultaneously charge multiple lithium batteries in parallel. Using this method, you can significantly reduce the time required for charging multiple battery packs.

If your charger is capable of supplying enough charge current, you can charge 4 batteries in the time it would normally take to charge each battery individually. This means you can spend 1/4 as much time charging and more time flying!

The ParaBoard is made of high quality components. The PCB is made of two ounce copper and the main power circuit is heavily tinned to allow the use of high current. The boards have been individually tested under 25A continuous current, and they are safe to be loaded at 35A for shorter periods of time (10 Minutes Max)

Features:
Charges up to 4 packs in parallel
Expandable for more boards via the "Export" ports
Housing Material: ABS Fireproof Material

Specifications:
Balance Tap: JST-XH
Cell Count: 2-6s
Fuse: 40A (4 fuses)
Size: 152x76x17.5mm
Maximum continuous current: 25A
Maximum current for short term: 35A (10 Minutes Max)
Please follow all precautions included in manual before using this board for parallel charging. Not following these directions may result in fire and damages. Austars Model is not responsible for damaged batteries or property.
Batteries should ALWAYS be the same cell count
Batteries should ALWAYS have nearly the same voltage before charging
Never leave your charger unattended Keep away from flammable materials. Always connect balance taps before main power plugs when connecting to the board

Parallel balance/charging board for 2-6s lithium polymer batteries with XT60 Connectors and JST-XH type balance connectors. You can use the parallel balance board to vastly reduce your charging time. For example if you have 3 of 2,200mAh 3s Li-Po batteries which you usually charge at 1C (2.2A), this would usually take approximately 3 hours to charge each pack individually. With this balance board you can charge all three packs in about one hour.

This parallel balance board can be used to parallel charge and balance up to 6 lithium polymer batteries of the same cell count. We recommend that all cells should be within 0.1V of each other.
The balance connector from the board is a 6s JST-XH type. The charging lead from the board is standard 4mm charge leads, which should fit most chargers.
Maximum throughput, 40A. This board is fused.
Do not mix cell counts (i.e. do not try to parallel charge a 3s and 4s pack)
Do ensure that all cells are within 0.1V of each other before connecting
Do connect the main charge leads of the packs to the board before connecting the balance leads.

Features:

ABS Fireproof Material 2 oz PCB + Heavily Tinned 40A Fuse can be replaced Double insurance ( 4 Packs ParaBoard ) Super quality rc connectors High-end atmospheric grade Perfect design Quick-acting Charging
Specification: 6 Packs paraBoard ( Fuse 40A ) 4 Packs paraBoard ( Fuse 40A + 1.85A / 1.1A ) Housing material : ABS Fireproof Material Color : Black & Blue

Parallel balance/charging board for 2-6s lithium polymer batteries with XT60 Connectors and JST-XH type balance connectors. You can use the parallel balance board to vastly reduce your charging time. For example if you have 3 of 2,200mAh 3s Li-Po batteries which you usually charge at 1C (2.2A), this would usually take approximately 3 hours to charge each pack individually. With this balance board you can charge all three packs in about one hour*.
This parallel balance board can be used to parallel charge and balance up to 6 lithium polymer batteries of the same cell count. We recommend that all cells should be within 0.1V of each other.

The balance connector from the board is a 6s JST-XH type. The charging lead from the board is standard 4mm charge leads, which should fit most chargers.
Maximum throughput, 40A. This board is fused.
Do not mix cell counts (i.e. do not try to parallel charge a 3s and 4s pack)
Do ensure that all cells are within 0.1V of each other before connecting
Do connect the main charge leads of the packs to the board before connecting the balance leads.

Features:ABS Fireproof Material 2 oz PCB + Heavily Tinned 40A Fuse can be replaced Double insurance ( 4 Packs ParaBoard ) Super quality rc connectors High-end atmospheric grade Perfect design Quick-acting Charging
Specification: 6 Packs paraBoard ( Fuse 40A ) 4 Packs paraBoard ( Fuse 40A + 1.85A / 1.1A ) Housing material : ABS Fireproof Material Color : Black & Blue

Parallel balance/charging board for 2-6s lithium polymer batteries with XT60 Connectors and JST-XH type balance connectors. You can use the parallel balance board to vastly reduce your charging time. For example if you have 3 of 2,200mAh 3s Li-Po batteries which you usually charge at 1C (2.2A), this would usually take approximately 3 hours to charge each pack individually. With this balance board you can charge all three packs in about one hour.

This parallel balance board can be used to parallel charge and balance up to 6 lithium polymer batteries of the same cell count. We recommend that all cells should be within 0.1V of each other.
The balance connector from the board is a 6s JST-XH type. The charging lead from the board is standard 4mm charge leads, which should fit most chargers.
Maximum throughput, 40A. This board is fused.
Do not mix cell counts (i.e. do not try to parallel charge a 3s and 4s pack)
Do ensure that all cells are within 0.1V of each other before connecting
Do connect the main charge leads of the packs to the board before connecting the balance leads.

Features:

ABS Fireproof Material 2 oz PCB + Heavily Tinned 40A Fuse can be replaced Double insurance ( 4 Packs ParaBoard ) Super quality rc connectors High-end atmospheric grade Perfect design Quick-acting Charging
Specification: 6 Packs paraBoard ( Fuse 40A ) 4 Packs paraBoard ( Fuse 40A + 1.85A / 1.1A ) Housing material : ABS Fireproof Material Color : Black & Blue

Parallel balance/charging board for 2-6s lithium polymer batteries with XT60 Connectors and JST-XH type balance connectors. You can use the parallel balance board to vastly reduce your charging time. For example if you have 3 of 2,200mAh 3s Li-Po batteries which you usually charge at 1C (2.2A), this would usually take approximately 3 hours to charge each pack individually. With this balance board you can charge all three packs in about one hour.

This parallel balance board can be used to parallel charge and balance up to 6 lithium polymer batteries of the same cell count. We recommend that all cells should be within 0.1V of each other.
The balance connector from the board is a 6s JST-XH type. The charging lead from the board is standard 4mm charge leads, which should fit most chargers.
Maximum throughput, 40A. This board is fused.
Do not mix cell counts (i.e. do not try to parallel charge a 3s and 4s pack)
Do ensure that all cells are within 0.1V of each other before connecting
Do connect the main charge leads of the packs to the board before connecting the balance leads.

Features:

ABS Fireproof Material 2 oz PCB + Heavily Tinned 40A Fuse can be replaced Double insurance ( 4 Packs ParaBoard ) Super quality rc connectors High-end atmospheric grade Perfect design Quick-acting Charging
Specification: 6 Packs paraBoard ( Fuse 40A ) 4 Packs paraBoard ( Fuse 40A + 1.85A / 1.1A ) Housing material : ABS Fireproof Material Color : Black & Blue

Parallel balance/charging board for 2-6s lithium polymer batteries with XT60 Connectors and JST-XH type balance connectors. You can use the parallel balance board to vastly reduce your charging time. For example if you have 3 of 2,200mAh 3s Li-Po batteries which you usually charge at 1C (2.2A), this would usually take approximately 3 hours to charge each pack individually. With this balance board you can charge all three packs in about one hour.

This parallel balance board can be used to parallel charge and balance up to 6 lithium polymer batteries of the same cell count. We recommend that all cells should be within 0.1V of each other.
The balance connector from the board is a 6s JST-XH type. The charging lead from the board is standard 4mm charge leads, which should fit most chargers.
Maximum throughput, 40A. This board is fused.
Do not mix cell counts (i.e. do not try to parallel charge a 3s and 4s pack)
Do ensure that all cells are within 0.1V of each other before connecting
Do connect the main charge leads of the packs to the board before connecting the balance leads.

Features:

ABS Fireproof Material 2 oz PCB + Heavily Tinned 40A Fuse can be replaced Double insurance ( 4 Packs ParaBoard ) Super quality rc connectors High-end atmospheric grade Perfect design Quick-acting Charging
Specification: 6 Packs paraBoard ( Fuse 40A ) 4 Packs paraBoard ( Fuse 40A + 1.85A / 1.1A ) Housing material : ABS Fireproof Material Color : Black & Blue

Parallel balance/charging board for 2-6s lithium polymer batteries with XT60 Connectors and JST-XH type balance connectors. You can use the parallel balance board to vastly reduce your charging time. For example if you have 3 of 2,200mAh 3s Li-Po batteries which you usually charge at 1C (2.2A), this would usually take approximately 3 hours to charge each pack individually. With this balance board you can charge all three packs in about one hour.

This parallel balance board can be used to parallel charge and balance up to 6 lithium polymer batteries of the same cell count. We recommend that all cells should be within 0.1V of each other.
The balance connector from the board is a 6s JST-XH type. The charging lead from the board is standard 4mm charge leads, which should fit most chargers.
Maximum throughput, 40A. This board is fused.
Do not mix cell counts (i.e. do not try to parallel charge a 3s and 4s pack)
Do ensure that all cells are within 0.1V of each other before connecting
Do connect the main charge leads of the packs to the board before connecting the balance leads.

Features:

ABS Fireproof Material 2 oz PCB + Heavily Tinned 40A Fuse can be replaced Double insurance ( 4 Packs ParaBoard ) Super quality rc connectors High-end atmospheric grade Perfect design Quick-acting Charging
Specification: 6 Packs paraBoard ( Fuse 40A ) 4 Packs paraBoard ( Fuse 40A + 1.85A / 1.1A ) Housing material : ABS Fireproof Material Color : Black & Blue

Parallel balance/charging board for 2-6s lithium polymer batteries with XT60 Connectors and JST-XH type balance connectors. You can use the parallel balance board to vastly reduce your charging time. For example if you have 3 of 2,200mAh 3s Li-Po batteries which you usually charge at 1C (2.2A), this would usually take approximately 3 hours to charge each pack individually. With this balance board you can charge all three packs in about one hour*.
This parallel balance board can be used to parallel charge and balance up to 6 lithium polymer batteries of the same cell count. We recommend that all cells should be within 0.1V of each other.
The balance connector from the board is a 6s JST-XH type. The charging lead from the board is standard 4mm charge leads, which should fit most chargers.
Maximum throughput, 40A. This board is fused.

Do not mix cell counts (i.e. do not try to parallel charge a 3s and 4s pack)
Do ensure that all cells are within 0.1V of each other before connecting
Do connect the main charge leads of the packs to the board before connecting the balance leads.

Features:? ABS Fireproof Material 2 oz PCB + Heavily Tinned 40A Fuse can be replaced Double insurance ( 4 Packs ParaBoard ) Super quality rc connectors High-end atmospheric grade Perfect design Quick-acting Charging
Specification: 6 Packs paraBoard ( Fuse 40A ) 4 Packs paraBoard ( Fuse 40A + 1.85A / 1.1A ) Housing material : ABS Fireproof Material Color : Black & Blue

New Austars ParaBoard is designed to be used in conjunction with a balance charger to simultaneously charge multiple lithium batteries in parallel. Using this method, you can significantly reduce the time required for charging multiple battery packs.

If your charger is capable of supplying enough charge current, you can charge 4 batteries in the time it would normally take to charge each battery individually. This means you can spend 1/4 as much time charging and more time flying!
The ParaBoard is made of high quality components. The PCB is made of two ounce copper and the main power circuit is heavily tinned to allow the use of high current. The boards have been individually tested under 25A continuous current, and they are safe to be loaded at 35A for shorter periods of time (10 Minutes Max)

Features:
Charges up to 4 packs in parallel
Expandable for more boards via the "Export" ports
Housing Material: ABS Fireproof Material

Specifications:
Balance Tap: JST-XH
?Cell Count: 2-6s
Fuse: 40A (4 fuses)
Size: 152x76x17.5mm
Maximum continuous current: 25A
Maximum current for short term: 35A (10 Minutes Max)
Please follow all precautions included in manual before using this board for parallel charging. Not following these directions may result in fire and damages. Austars Model is not responsible for damaged batteries or property.
Batteries should ALWAYS be the same cell count
Batteries should ALWAYS have nearly the same voltage before charging
Never leave your charger unattended Keep away from flammable materials. Always connect balance taps before main power plugs when connecting to the board

This is the Austars Multi-Port Safe Parallel Adapter. This version supports LiPo batteries with JST XH compatible balance connectors and wiring. Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, and other charger brands compatible with JST XH balance connectors and wiring.

Features:
Support for safe parallel charging of up to 6 same-cell-count packs at one time (2s-8s)
Supports 40A max charge/discharge rate
Every port reverse polarity fuse protection of main battery wires
Every cell/balance wire protected by self-resetting polyfuses with temperature warning indicators
Supports non-balanced charge of up to two 1s LiPos used with "indoor models"
Supports 1 RX and 1 TX NiCd/NiMH battery pack. Works with any Cellpro charger or battery workstation equipped with XH wiring.

Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, as well as other brand chargers which are compatible with XH balance plugs and wiring. Be sure to purchase the proper cable to plug the MPA6 into your Charger or Battery Workstation